Congatec conga-IA3 User Manual Download Page 59

Page: 59 / 82

2015

congatec

IA30m10

59/82

8.4.4

Trusted Computing Submenu

Feature

Options

Description

Security Device Support

Disabled

Enabled

Enable or disable TPM support. System reset is required after change.

User Confirmation

Disabled

Enabled

Enable or disable user confirmation requests for certain transactions.

TPM State

Disabled

Enabled

Enable or disable TPM chip.
Note: System might restart several times during POST to acquire target state.

Pending operation

None,

Enable Take Ownership,
Disable Take Ownership,
TPM Clear

Perform selected TPM chip operation.
Note: System might restart several times during POST to perform selected operation.

8.4.5

RTC Wake Submenu

Feature

Options

Description

Wake System At Fixed Time

Disabled

Enabled

Enable system to wake from S5 using RTC alarm.

Wake up hour

Specify wake up hour. For example, enter “3” for 3am and “15” for 3pm.

Wake up minute

Specify wake up minute.

Wake up second

Specify wake up second.

8.4.6

Reserve Legacy Interrupt Submenu

Feature

Options

Description

Reserve Legacy Interrupt 1

None, IRQ3, IRQ4, IRQ5,
IRQ6, IRQ10, IRQ11, IRQ14,
IRQ15

The interrupt reserved here will not be assigned to any PCI or PCI Express device and thus maybe available for
some legacy bus device.

Reserve Legacy Interrupt 2

Same as Reserve Legacy
Interrupt 1

Same as Reserve Legacy Interrupt 1

Reserve Legacy Interrupt 3

Same as Reserve Legacy
Interrupt 1

Same as Reserve Legacy Interrupt 1

Summary of Contents for conga-IA3

















































































Search results

Summary of Contents for conga-IA3

Reviews:

Related manuals for conga-IA3

Brands by name

Popular brands

Congatec conga-IA3, User Manual

Search results

Summary of Contents for conga-IA3

Reviews:

Related manuals for conga-IA3

Brands by name

Popular brands