Condair Nortec RS 10 Engineering Manual Download Page 11

Page: 11 / 72

Nortec RS Steam Humidifier

2596995_0_EN_1905

Nortec RS

Table 3: Nortec RS Accessories, continued...

Accessory

Description

Condensate pump

High temperature condensate pump for pumping waste water from the Nortec RS or conden-

sate from the distributor systems.

1429527 – Drain water sump pump, low flow

2524504 – Electric sump pump, medium flow

2576898 – Electric sump pump, high flow

Drain air gap reducer

All Nortec RS humidifiers require an air gap in the drain line as close as possible to the hu-

midifier. The air gap reducer is a 2-1/2 in to 7/8 in (63.5 mm to 22 mm) fitting that can provide

the required air gap.

2522172 – External drain air gap reducer

Pocket hygro-thermometer

digital display

The pocket hygro-thermometer provides a means to check the humidity and temperature in a

space. It is a useful tool for troubleshooting humidity problems.

1469595 – Pocket hygro-thermometer digital display

Transformer, plug-In,

120 VAC to 24 VAC

AC adaptor 120 VAC to 24 VAC, 40 VA for providing power to remote electronics/controls.

1603032 – Transformer, plug-In, 120 VAC to 24 VAC

Summary of Contents for Nortec RS 10









































































Search results

Summary of Contents for Nortec RS 10

Reviews:

Related manuals for Nortec RS 10

Brands by name

Popular brands

Condair Nortec RS 10, Engineering Manual

Search results

Summary of Contents for Nortec RS 10

Reviews:

Related manuals for Nortec RS 10

Brands by name

Popular brands