20
21
Avoid exposing the treated areas to sun. Protect your skin with a
sunscreen throughout the treatment and for at least two weeks
after the last session with your Lumilisse Hair Remover.
Do not use scented cream or deodorant on the treated areas after
your sessions.
Side eff ects and complications
Some users may notice a change in pigmentation following a
treatment with the Lumilisse Hair Remover. These eff ects, if they
appear, are generally slight and temporary.
If you experience complications
,
stop using the appliance
immediately and contact your healthcare provider.
8. Lifespan of your Lumilisse Hair Remover
8.1 Lifespan
With an exceptionally long life, the Lumilisse Hair Remover fl ash lamp releases all its
light pulses without a decline in energy.
When the unit is at the end of its life, the ON/OFF indicator light will
fl ash
orange. The
unit is now permanently disabled.
Do not use the unit if large stains appear inside the fl ash
lamp or if the application surface is broken. Contact Conair
Customer Service.
9. Troubleshooting
9.1 My Lumilisse Hair Remover won’t start
Ensure the adapter is properly connected to your Lumilisse Hair Remover and plugged
into a wall outlet.
9.2 There are no pulses when I press the release mechanism
Ensure that the application surface is evenly and fi rmly in contact with your skin and that the
Ready indicator light is fl ashing; this indicator light guarantees that the unit is in full contact
with your skin. For your safety, the release switch will be able to release a pulse only if the
application surface is fi rmly pressed against your skin.
Make sure the Ready light is lit.
• If after 10 seconds the Ready light is still off , switch your Lumilisse Hair Remover off
and on again by pressing the ON/OFF button twice.
• If the problem persists, contact Conair customer service.
Make sure the ON indicator light is lit.
• If it is lit, switch your Lumilisse Hair Remover off and on again by pressing the
ON/OFF button.
• If the problem persists, contact Conair Customer Service.
The ON/OFF indicator light is orange.
• The unit has switched to the safety mode because it has detected that it is overheated
or there is a critical problem. Under circumstances like these, switch the unit off and
allow it to cool for 15 minutes before switching it on again.
• If the problem persists, contact Conair Customer Service.
• The Lumilisse Hair Remover is not suitable for treating men’s beards.
• For your comfort and safety, we recommend that you have someone help you use the
Lumilisse Hair Remover on your face for the first few sessions, once they have familiarized
themselves with the instruction manual.
•
NOTE:
The Glide mode is not available for facial depilation.
• You must wait 5 seconds between each pulse of light when using the device on the face.
Any facial depilation session with the Lumilisse Hair Remover must not last any longer
than 10 minutes.
Positioning the special facial attachment
To fit or remove the facial attachment, the device must be switched off and unplugged.
Gently grasp the facial attachment between the thumb and index finger to fit or remove it.
NOTE:
Remove the facial attachment and place the body attachment on the Lumilisse
Hair Remover appliance to treat legs, back and arms.
WARNING:
Hot surfaces. Do not touch the application surface of the facial attachment
with your fingers.
NOTE:
The Lumilisse Hair Remover has a system to protect your eyes, a contact sensor
that prevents the unit from releasing a pulse if its application surface is not in full
contact with your skin. If the unit is not in full contact with your skin, it will not release
a pulse of light. Make sure, therefore, that the application window touches your skin
on all sides so that the safety contact sensors are touching your skin on all sides around
the fl ash lens.
NOTE:
The Lumilisse Hair Remover will turn off automatically if you do not use the
device for more than 10 minutes. The ON/OFF button is now orange. To use the
Lumilisse Hair Remover again, you have to press the ON/OFF button and select the
required level of intensity again.
7.1 Switching off the Lumilisse Hair Remover
At the end of your depilation session, switch off the Lumilisse Hair Remover by pressing
the ON/OFF button.
Unplug the adapter from the power outlet.
Storage: When not in use, your device should be disconnected and stored in a safe, dry
location out of the reach of children.
7.2 Cleaning
We recommend that you clean the Lumilisse Hair Remover, especially the application
window, before every depilation session. Do not clean after use because the unit may
be hot.
• Unplug the Lumilisse Hair Remover before cleaning.
• Gently clean the casing of the Lumilisse Hair Remover and especially the application
surface, using a clean, dry cloth. Do not use harsh chemicals.
• After cleaning, store the Lumilisse Hair Remover in its original box in a dry, safe place.
• Never immerse your Lumilisse Hair Remover, or any of its parts in water.
7.3 Caring for the skin following an epilation session with the Lumilisse Hair Remover
7. After using the Lumilisse Hair Remover
ipl960f_18pg025882_ib_final.indd 20-21
ipl960f_18pg025882_ib_final.indd 20-21
3/13/18 8:12 AM
3/13/18 8:12 AM
