manualshive.com logo in svg

Comtrol InterChange VS 3000 Series, Installation And Configuration Manual

Share
Download
Comtrol InterChange VS 3000 Series Installation And Configuration Manual Download Page 75

75

Error Codes and System Messages

CAPI3000 E319:

No Bn data buffers available for Virtual Server 
aaaaaaaa/Port p!

A send B channel data request to VS3000 aaaaaaaa, port 
p, was rejected due to an empty B channel transmit buffer 
header pool. The request is rejected.

CAPI3000 E320:

Insufficient transmit ECBs available for Virtual Server 
aaaaaaaa/Port p/Bn, NIC dd, status <0xhh>!

A send B channel data request to VS3000 aaaaaaaa, port 
p, channel Bn, on NIC dd was rejected due to a lack of 
system ECBs. The request is rejected.

CAPI3000 E321:

Virtual Server aaaaaaaa in sss...sss state, unavailable for 
output!

An output request was rejected due to VS3000 aaaaaaaa 
having a current state of sss...sss.

CAPI3000 E322:

Unable to send packet, status <0xhhhhhh> on Virtual 
Server aaaaaaaa/Port p/Bn, NIC dd!

A send B channel data request to VS3000 aaaaaaaa, port 
p, channel Bn, on NIC dd was issued but rejected by LSL 
for status hh. The request is rejected. If hhhhhhhh = 
0FFFFF85, the board number dd was invalid. No other 
statuses are defined.

CAPI3000 E400:

CAPI Data B3 Request: Virtual Server aaaaaaaa/Port p/
Bn: Send failure, NCCI <0xhhhhhhhh>!

A send B channel data request to VS3000 aaaaaaaa, port 
p, channel Bn, on NIC dd (Network Control Connection 
ID hhhhhhhh) was rejected. 

CAPI3000 E401:

CAPI Data B3 Request: Virtual Server aaaaaaaa/Port p/
Bn: Unable to acquire buffer, NCCI <0xhhhhhhhh>!

A send B channel data request to VS3000 aaaaaaaa, port 
p, channel Bn, on NIC dd (Network Control Connection 
ID hhhhhhhh) failed due to an empty transmit buffer 
header pool. The request is rejected.

CAPI3000 E402:

Unable to identify and process 'VS' event 0xhh!

An event hh associated with the VS3000 was queued and 
signalled, but could not be identified. The event is 
discarded.

Table 6. CAPI3000 Error Codes

Code

Message and Description

Summary of Contents for InterChange VS 3000 Series



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands