manualshive.com logo in svg

Comtrol InterChange VS 3000 Series, Installation And Configuration Manual

Share
Download
Comtrol InterChange VS 3000 Series Installation And Configuration Manual Download Page 68

68

Error Codes and System Messages

CAPI3000 E031: 

Unable to allocate nnnn bytes for firmware file bbbbbbbb, 
Virtual Server aaaaaaaa not loaded!

Could not allocate sufficient space for the optional 
firmware file firmware. Fatal, as driver won’t default to 
standard driver. If the standard driver is acceptable, 
reconfigure the VS3000 to remove the optional firmware 
file name and restart the server.

CAPI3000 E032:

Read error on firmware file bbbbbbbb, Virtual Server 
aaaaaaaa not loaded!

System returned an error attempting to read the optional 
firmware file. Fatal, as driver won’t default to standard 
driver. If the standard driver is acceptable, reconfigure 
the VS3000 to remove the optional firmware file name 
and restart the server.

CAPI3000 E033: 

Unable to unload driver - connections still active!

Driver unload failed, since calls are still active. The 
driver cannot force calls down. That must be done by the 
owning application or by Novell Call Manager.

CAPI3000 E034:

Virtual Server aaaaaaaa (#dd) de-registration failed!

Unable to deregister the driver from the application. 
Server may need to be brought down and back up.

CAPI3000 E035:

Error allocating CAPI Data Buffer pool (nnnn bytes)!

Insufficient space for inbound data buffer pool. This pool 
is built on an application basis using the values passed 
from the application and CAPI manager at registration, 
and is related to the Command Buffer pool. Fatal.

CAPI3000 E036:

Error allocating CAPI Command Buffer Pool (nnnn 
bytes)!

Insufficient space for outbound inbound buffer pool of 
nnnn bytes. This pool is built on an application basis 
using the values passed from the application and CAPI 
manager at registration, and is related to the CAPI Data 
Buffer pool. Fatal.

CAPI3000 E037: 

Error allocating buffer header pool (nnnn bytes)!

Insufficient space for outbound buffer headers of nnnn 
bytes. This pool is built on an application basis. Fatal.

Table 6. CAPI3000 Error Codes

Code

Message and Description

Summary of Contents for InterChange VS 3000 Series



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands