manualshive.com logo in svg

Comtrol InterChange VS 3000 Series, Installation And Configuration Manual

Share
Download
Comtrol InterChange VS 3000 Series Installation And Configuration Manual Download Page 17

Installing VS-Link for Novell

17

Installing VS-Link (Novell)

4.

Press the 

Insert

 key.

A message displays, telling you to either insert the installation disk 
in the A:\ drive or specify the path to the installation files:

5.

If you are installing from the 

InterChangeVS 3000

 diskette supplied 

with the VS3000 (Part Number: 6620), follow these steps:

a.

Place the diskette in the 

A:

 drive.

b.

Press 

F3

. You are prompted to specify a directory path.

c.

Enter 

A:\NOVELL

 and press 

Enter

.

-OR-

If you are installing from an installation diskette that you created 
from a downloaded zip file, follow these steps:

a.

Place the diskette in the 

A:

 drive.

b.

Press 

Enter

.

In either case, the installation utility examines the specified drive 
and directory for the 

pscript.dat

 installation file. When the file is 

found, the Comtrol InterChangeVS 3000 Installation Options 
menu is displayed. At this point you can display the installation log 
file, display the 

README

 file(s), or install the software.

It is good practice to review the README files before proceeding.

Summary of Contents for InterChange VS 3000 Series



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands