manualshive.com logo in svg

Comtrol InterChange VS 3000 Series, Installation And Configuration Manual

Share
Download
Comtrol InterChange VS 3000 Series Installation And Configuration Manual Download Page 64

64

Error Codes and System Messages

CAPI3000 E004:

Error, cannot register more than n applications, rejected!

Since buffer pools and other resources are dedicated to 
each particular application, more than a certain number 
would have adverse impact on performance. This console 
message indicates that an application has attempted to 
register with the VS3000 stack after all available 
application slots were registered. 

Note: PPP is considered one application

CAPI3000 E005:

Error allocating application control structure!

Application registration failed due to lack of available 
memory. Error returned to CAPI, registration failed.

CAPI3000 E006:

Error, illegal Application ID nn!

Release by unrecognized application failed, application 
identifier is too large, should be from the set {0-3}. Error 
returned to CAPI, registration failed.

CAPI3000 E007:

Error, application not found for ID nn!

Release by unrecognized application failed, application 
identifier was not in use. Error returned to CAPI, 
registration failed.

CAPI3000 E008:

Error, stale Application ID nn!

Release by unrecognized application failed, application 
identifier supplied by application didn't match one 
retained by VS3000 ISDN driver. Error returned to CAPI, 
registration failed.

CAPI3000 E009: 

Error, invalid CAPI subcommand <0xhh>!

The CAPI subcommand (properly either a request or 
response) was unrecognized and the command was 
discarded with an error response to CAPI. Valid 
subcommands are {80, 81, 82, 83}.

CAPI3000 E010: 

Insufficient memory available for virtual server 
information!

Couldn't allocate sufficient space for interface 
configuration data. Fatal, since driver initialization fails.

Table 6. CAPI3000 Error Codes

Code

Message and Description

Summary of Contents for InterChange VS 3000 Series



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands