Comtrend Corporation WR-6891u User Manual Download Page 26 | Manualshive

Page: 26 / 81

background image

25

4.7 IGMP Proxy

Field

Description

Interface

The Source interface from which the IGMP report was received

WAN

The WAN interface from which the multicast traffic is received

Groups

The destination IGMP group address

Member

The Source IP from which the IGMP report was received

Timeout

The time remaining before the IGMP report expires

«
...
24
25
26
27
28
...
»

Summary of Contents for WR-6891u


















































































Reviews:

No comments

Related manuals for WR-6891u

Brand: ICP DAS USA Pages: 8

Brand: RTA Pages: 66

NETWORK INTERFACE CARDS

Brand: Secure Computing Pages: 17

Brand: RTA Pages: 72

Brand: ICU tech Pages: 17

Brand: 3onedata Pages: 44

NFS/DFS Secure Gateway

Brand: IBM Pages: 67

Brand: Synway Pages: 7

Brand: TANDBERG Pages: 39

Brand: RTA Pages: 68

Brand: Ascent Communication Technology Pages: 114

Brand: Mako Pages: 70

Brand: IFM Pages: 131

Brand: Intermatic Pages: 6

Brand: 2Wire Pages: 30

Brand: Hitron Pages: 2

Brand: Hitron Pages: 12

Brand: FireAngel Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands