Configuration
SDM-9000 Satellite Modem
3–14
Rev. 4
3.6 Software Configuration
This section consists of the following software information:
•
Revision emulation feature
•
Programming the remote baud rates/addresses
•
Modem defaults
3.6.1 Revision Emulation
The modem includes a revision emulation feature that allows the user to program an
emulation mode of a previous functional revision. This feature is accessed through the
Utility Modem Type menu (refer to Chapter 4). The user can emulate Version 1.1.1
through the current version by selecting a functional number at the Rev. Emulation menu
(refer to Table 3-5).
Table 3-5. SDM-9000 Revision Emulation
Functional #
Software
Version
Firmware #
Description of Change
1
1.1.1
4100-1-
Original version
2
2.1.1
4100-1A
Software changes
3
3.1.1
4100-1B
Software changes
3
3.1.2
4100-1C
Correctional Setting
4
4.1.1
4100-1D
Software changes
5
5.1.1
4100-1E
Software changes
6
6.1.1
4100-1F
Software changes
Notes:
1. Programming a functional number (1 through X) eliminates all changes
(disables new features/options) for the later version numbers. For example,
functional number 3 may eliminate some features/options for Version 4.1.1
or greater.
2. Programming Current Version (default) allows all features and options to
operate (if installed).
3. The user must manually program the functional version on a cold-start
(default is Current Version).
4. Revision emulation will not affect some user interface changes that do not
affect direct operation of the modem. For example: Configuration
Save/Recall; cosmetic changes; Test Mode screen in the Utility System
menu; all Factory Setup modes, and so forth.
Summary of Contents for SDM-9000
