Remote Control Operation
SDM-9000 Satellite Modem
B–22
Rev. 4
Bulk
Consol.
Status
Command:
Response:
<add/BCS_'cr'
>add/BCS_p1,p2,p3, . . . pn'cr''lf']
This command causes bulk modem status to be returned. To
reduce the length of the response, message parameter data
are returned without identifiers. However, parameter
identification can be determined by order of return. Each status
parameter is terminated with a ',' (comma), except for the last
parameter, which has the standard message termination
sequence ('cr''lf']). Most of the data returned is formatted the
same way as the single command status request (refer to the
appropriate portions of this document in preceding sections).
Where: 'pn' is the last parameter returned.
Parameter
Number
Parameter Name
(Command Reference)
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Modulator RF output
(ref. 'RF_' command).
Modulator IF frequency
(ref. 'MF_' command).
Modulator rate
(ref. 'MR_' command).
Modulator preset 'A' assignment
(ref. 'ARMA_' command).
Modulator preset 'B' assignment
(ref. 'ARMB_' command).
Modulator preset 'C' assignment
(ref. 'ARMC_' command).
Modulator preset 'D' assignment
(ref. 'ARMD_' command).
Modulator power offset
(ref. 'MPO_' command).
Modulator output power level
(ref. 'MOP_' command).
Differential encoder enable
(ref. 'DENC_' command).
Carrier only mode ON/OFF
.
Modulator Spectrum Rotation
(ref. 'MSR_' command).
Modulator Reference Clock
(ref. 'MRC_' command).
Reed-Solomon Encoder Enable
(ref. 'RSEN_' command).
Demodulator IF frequency
(ref. 'DF_' command).
Demodulator rate
(ref. 'DR_' command).
p1 = n, where 'n' is '0' (OFF) or '1' (ON).
p2 = nnn.nnnn, IF frequency in MHz.
p3 = nnnnn_mmmmm.mmm, code rate/data rate in kbit/s.
p4 = nnnnn_mmmmm.mmm, code rate/data rate in kbit/s.
p5 = nnnnn_mmmmm.mmm, code rate/data rate in kbit/s.
p6 = nnnnn_mmmmm.mmm, code rate/data rate in kbit/s.
p7 = nnnnn_mmmm.mmm, code rate/data rate in kbit/s.
p8 = snn.n, modulator power offset in dB.
p9 = snn.n, transmitter output power level in dBm.
p10 = n, where 'n' is '0' (OFF) or '1' (ON).
p11 = n, where 'n' is '0' (OFF) or '1' (ON).
p12 = n, where 'n' is '0' (NRM) or '1' (INV).
p13 = n, where 'n' is '0' (INT), '1' (EXT5), '2' (EXT10), or
'3' (EXT20).
p14 = n, where 'n' is '0' (OFF) or '1' (ON).
p15 = nnn.nnnn, demodulator IF frequency in MHz.
p16 = nnnnn_mmmmm.mmm, code rate/data rate in kbit/s.
Summary of Contents for SDM-9000
