Comtech EF Data SDM-9000, Installation And Operation Manual

Page: 247 / 256

SDM-9000 Satellite Modem Remote Control Operation
Rev. 4 B–29
Where: Character 'p': Interface Reed-Solomon Unavailable
Seconds.
Bit 6 = 1 always.
Bit 5 = not used.
Bit 4 = not used.
Bit 3 through Bit 0 = Binary representation (0 to 10) of the
number of Reed-Solomon Unavailable Seconds stored faults.
Change
Status Command
:
Response: <add/CS_'cr'
>add/CS_x'cr''lf'] Where: 'x' character is defined as follows:
@ = No change since last BCS_ and BCSF_ polls.
A = BCS_ response has changed since last BCS_ poll.
B = BCSF_ response has changed since last BCSF_ poll.
C = Both responses have changed since last BCS_ and
BCSF_ polls.
This command indicates that a change has or has not occurred
on either the BCS_ or the BCSF_ response since the last BCS_
or BCSF_ poll.
Equipment
Type Command
:
Response: <add/ET_'cr'
>add/ET_tttttttt_xxx.yyy.zzz'cr''lf'] Where:
tttttttt = Equipment type.
xxx.yyy.zzz = Software version.
M&C
Firmware
Information Command
:
Response: <add/MCFI_'cr'
>add/MCFI_'cr'
VER_xxx.yyy.zzz'cr'
FW/nnnnnn-ddr'cr'
mm/dd/yy'cr''lf'] Where:
xxx.yyy.zzz = Software version number (0.0.0 to
999.999.999).
nnnnnn = Firmware number (0 to 999999).
dd = Firmware dash number (0 to 99).
r = Firmware revision (-, or A to Z).
Modulator
Firmware
Information Command
:
Response: <add/MFI_'cr'
>add/MFI_'cr'
VER_xxx.yyy.zzz'cr'
FW/nnnnnn-ddr'cr'
mm/dd/yy'cr'
FPGA_FW/nnnnnn-ddr'cr'
FPGA_mm/dd/yy'cr'
FILTER_FW/nnnnnn-ddr'cr'
FILTER_mm/dd/yy'cr''lf'] Where:
xxx.yyy.zzz = Software version number (0.0.0 to
999.999.999).
nnnnn = Firmware number (0 to 999999).
dd = Firmware dash number (0 to 99).
r = Firmware revision (-, or A to Z).
Demodulato
r Firmware
Information Command
:
Response: <add/DFI_'cr'
>add/DFI_'cr'
VER_xxx.yyy.zzz'cr'
FW/nnnnnn-ddr'cr'
mm/dd/yy'cr'
FPGA_FW/nnnnnn-ddr'cr'
FPGA_mm/dd/yy'cr''lf'] Where:
xxx.yyy.zzz = Software version number (0.0.0 to
999.999.999).
nnnnnn = Firmware number (0 to 999999).
dd = Firmware dash number (0 to 99).
r = Firmware revision (-, or A to Z).
Interface
Firmware
Information Command
:
Response: <add/IFI_'cr'
>add/IFI_'cr'
VER_xxx.yyy.zzz'cr'
FW/nnnnnn-ddr'cr'
mm/dd/yy'cr'
FPGA_FW/nnnnnn-ddr'cr'
FPGA_mm/dd/yy'cr''lf'] Where:
xxx.yyy.zzz = Software version number (0.0.0 to
999.999.999).
nnnnnn = Firmware number (0 to 999999).
dd = Firmware dash number (0 to 99).
r = Firmware revision (-, or A to Z).
Modulator
Options/
Misc.
Information Command
:
Response: <add/MOI_'cr'
>add/MOI_'cr'
x,8PSK/16QAM'cr'
x,HIGH_STABILITY'cr''lf'] Where: x = 0 (option not installed) or 1 (option installed).