Compaq 3U RM Storage Enclosure Reference Manual Download

Page: 12 / 36

1-4

Compaq 3U RM Storage Enclosure Reference Guide

Compaq Confidential – Need to Know Required

Writer: Tricia Acevedo Project: Compaq 3U RM Storage Enclosure Reference Guide Comments:

Part Number: 232797-021 File Name: b-ch1 Introduction.doc Last Saved On: 2/12/01 2:29 PM

Hardware Options

!!"

Table 1-1

3U RM Storage Enclosure Options

Option

Part Number

Tape Drives

12/24-GB DAT Internal Tape Drive

295513-B22

20/40-GB DAT Internal Tape Drive

157769-B21

AIT 35 LVD Internal Tape Drive

216884-B21

AIT 50 Internal Tape Drive

157766-B21

20/40-GB DLT Internal Tape Drive

340743-B22

40/80-GB DLT Internal Tape Drive

146196-B21

110/220-GB SDLT Internal Tape Drive

192106-B21

20/40-GB DAT Internal Autoloader

166504-B21

Media

AIT 50-GB Data Cassette (five-pack)

152841-001

Type IV Media DLT Tape Cartridges (seven-pack)

295194-B21

SDLT Tape Cartridges (five-pack)

188527-B21

SDLT Tape Cartridges (ten-pack)

188527-B22

SDLT Tape Cartridges (twenty-pack)

188527-B26

AIT Cleaning Cartridge

402374-B21

DLT Cleaning Cartridge

199704-001

Miscellanous

LVD Cable Kit

168048-B21

3U Rail Extender Kit*

174574-B21

*NOTE: This option is required if you are using an Alpha “round hole” rack.

Summary of Contents for 3U RM Storage Enclosure





































Search results

Summary of Contents for 3U RM Storage Enclosure

Reviews:

Related manuals for 3U RM Storage Enclosure

Brands by name

Popular brands

Compaq 3U RM Storage Enclosure, Reference Manual

Search results

Summary of Contents for 3U RM Storage Enclosure

Reviews:

Related manuals for 3U RM Storage Enclosure

Brands by name

Popular brands