Compaq 3U RM Storage Enclosure Reference Manual Download | Manualshive

Page: 15 / 36

background image

Compaq Confidential – Need to Know Required

Writer: Tricia Acevedo Project: Compaq 3U RM Storage Enclosure Reference Guide Comments:

Part Number: 232797-021 File Name: c-ch2 Tape Drive Installation.doc Last Saved On: 2/9/01 11:50 AM

Chapter

2

Tape Drive Installation

Introduction

This chapter describes how to install a tape drive in the Compaq 3U RM
Storage Enclosure. Topics covered in this chapter include the following:

■

SCSI IDs

■

Removing and installing a tape drive

■

Cable configurations

■

Installing SCSI connectors

SCSI IDs

The default SCSI ID for each tape drive depends on the cable configuration
used in the storage enclosure. If there is one tape drive per SCSI cable, the
default is 0. For two tape drives per SCSI cable, the default for the top tape
drive is 1 and the default for the bottom tape drive is 0.

Before setting the SCSI ID, be sure the SCSI ID complies with the following:

■

Each SCSI device on the same SCSI bus must have a unique SCSI ID.

■

If the tape drives’ SCSI IDs need to be reassigned, do not duplicate
SCSI IDs.

■

Do not use SCSI ID 7 because it is reserved for the controller.

«
...
13
14
15
16
17
...
»

Summary of Contents for 3U RM Storage Enclosure





































Reviews:

No comments

Related manuals for 3U RM Storage Enclosure

MPG Gungir 110R EVA e-PROJECT

Brand: MSI Pages: 13

Brand: StarTech.com Pages: 13

Brand: Nordson EFD Pages: 24

Brand: schmersal Pages: 24

Brand: AMX Pages: 2

Dimmer Enclosures w/Breakers RDA-ENC12B

Brand: AMX Pages: 2

Brand: 3D Upfitters Pages: 17

Multi Hard Disk Box 2.5

Brand: Sandberg Pages: 24

Brand: iseg Pages: 20

Brand: Phanteks Pages: 2

Brand: Tranberg Pages: 8

Brand: YORKVILLE Pages: 1

Brand: YORKVILLE Pages: 14

Brand: Sentey Pages: 5

17/TRZ75/SATEL/GRADE3

Brand: Pulsar Pages: 4

U457-025-SATAG2

Brand: Tripp Lite Pages: 28

Brand: CRU Pages: 10

Brand: IC Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands