manualshive.com logo in svg

Comnet CNGE2FE8MSPOE2, Installation And Operation Manual

Share
Download
Comnet CNGE2FE8MSPOE2 Installation And Operation Manual Download Page 90

INS_CNGE2FE8MSPOE2_REV–

12/20/12     PAGE 90

INSTALLATION AND OPERATION MANUAL 

CNGE2FE8MSPOE2

TECH SUPPORT: 1.888.678.9427

Commands Set List—Spanning Tree command set 

Commands

Level Description

Example

spanning-tree enable

G

Enable spanning tree

switch(config)#spanning-tree enable

spanning-tree priority 
[0to61440]

G

Configure spanning tree priority 
parameter

switch(config)#spanning-tree priority 
32767

spanning-tree max-age 
[seconds]

G

Use the spanning-tree max-age 
global configuration command 
to change the interval between 
messages the spanning tree 
receives from the root switch. 
If a switch does not receive a 
bridge protocol data unit (BPDU) 
message from the root switch 
within this interval, it recomputed 
the Spanning Tree Protocol (STP) 
topology.

switch(config)# spanning-tree max-age 
15

spanning-tree  hello-
time [seconds]

G

Use the spanning-tree hello-time 
global configuration command 
to specify the interval between 
hello bridge protocol data units 
(BPDUs).

switch(config)#spanning-tree hello-
time 3

spanning-tree  forward-
time [seconds]

G

Use the spanning-tree forward-
time global configuration 
command to set the forwarding-
time for the specified spanning-
tree instances. The forwarding 
time determines how long each of 
the listening and 
learning states last before the port 
begins forwarding.

switch(config)# spanning-tree forward-
time 20

stp-path-cost 
[1to200000000] 

I

Use the spanning-tree cost 
interface configuration command 
to set the path cost for Spanning 
Tree
Protocol (STP) calculations. In the 
event of a loop, spanning tree 
considers the path cost when 
selecting an interface to place into 
the forwarding state.

switch(config)#interface fastEthernet 2
switch(config-if)#stp-path-cost 20

stp-path-priority
[Port Priority] 

I

Use the spanning-tree port-
priority interface configuration 
command to configure a port 
priority that is used when two 
switches tie for position as the 
root switch.

switch(config)#interface fastEthernet 2
switch(config-if)# stp-path-priority 127

Summary of Contents for CNGE2FE8MSPOE2










































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands