Comnet CNGE2FE8MSPOE2 Installation And Operation Manual Download Page 21

Page: 21 / 105

INS_CNGE2FE8MSPOE2_REV–

12/20/12 PAGE 21

INSTALLATION AND OPERATION MANUAL

CNGE2FE8MSPOE2

TECH SUPPORT: 1.888.678.9427

DB9 Male

DB9 Female

Pin Male Connector

Female Connector

Received Line Signal Detect (Received by DTE
Device)

Received Line Signal Detect (Transmitted from
DCE Device)

Received Data (Received by DTE Device)

Transmitted Data (Transmitted from DCE Device)

Transmitted Data (Transmitted from DTE Device)

Received Data (Received by DCE Device)

DTE Ready (Transmitted from DTE Device)

DTE Ready (Received by DCE Device)

Signal Ground

DCE Ready (Received by DTE Device)

DCE Ready (Transmitted from DCE Device)

Request to Send (Transmitted from DTE Device)

Clear to Send (Received by DCE Device)

Clear to Send (Received by DTE Device)

Request to Send (Transmitted from DCE Device)

Ring Indicator (Received by DTE Device)

Ring Indicator (Transmitted from DCE Device)

Summary of Contents for CNGE2FE8MSPOE2










































































































Search results

Summary of Contents for CNGE2FE8MSPOE2

Reviews:

Brands by name

Popular brands

Comnet CNGE2FE8MSPOE2, Installation And Operation Manual

Search results

Summary of Contents for CNGE2FE8MSPOE2

Reviews:

Brands by name

Popular brands