manualshive.com logo in svg

Comnet CNGE2FE8MSPOE2, Installation And Operation Manual

Share
Download
Comnet CNGE2FE8MSPOE2 Installation And Operation Manual Download Page 41

INS_CNGE2FE8MSPOE2_REV–

12/20/12     PAGE 41

INSTALLATION AND OPERATION MANUAL 

CNGE2FE8MSPOE2

TECH SUPPORT: 1.888.678.9427

Label

Description

MSTP Enable

Enable/disable MSTP function to configure the related parameters.

Force Version

The Force Version parameter can be used to force a VLAN Bridge 
that supports RSTP to operate in an STP-compatible manner.

Configuration Name The same MST Region must have the same MST configuration 

name.

Revision Level 
(0-65535)

The same MST Region must have the same revision level.

Priority (0-61440)

A value used to identify the root bridge. The bridge with the 
lowest value has the highest priority and is selected as the root. If 
the value changes, you must reboot the switch. The value must be 
a multiple of 4096 according to the protocol standard rule.

Max Age Time(6-40) Time, in seconds, a bridge will wait to receive Spanning-

tree Protocol configuration messages before attempting a 
reconfiguration. Enter a value 6 through 40.

Hello Time (1-10)

Follow the rule below to configure the MAX Age, Hello Time, 
and Forward Delay Time a controlled switch sends out the BPDU 
packet to check RSTP current status. 
Enter a value between 1 through 10.
2 x (Forward Delay Time value –1) ≥ Max Age value ≥ 2 x (Hello 
Time value +1)

Forwarding Delay 
Time (4-30)

Time, in seconds, a port will wait before changing from its Rapid 
Spanning-Tree Protocol learning and listening states to the 
forwarding state. Enter a value 4 through 30.

Max Hops (1-40)

This parameter is additional to those specified for RSTP. A single 
value applies to all Spanning Trees within an MST Region (the 
CIST and all MSTIs) for that the Bridge is the Regional Root.

Apply

Select 

Apply

 to activate the configurations.

Summary of Contents for CNGE2FE8MSPOE2










































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands