manualshive.com logo in svg

Comnet CNGE2FE8MSPOE2, Installation And Operation Manual

Share
Download
Comnet CNGE2FE8MSPOE2 Installation And Operation Manual Download Page 22

INS_CNGE2FE8MSPOE2_REV–

12/20/12     PAGE 22

INSTALLATION AND OPERATION MANUAL 

CNGE2FE8MSPOE2

TECH SUPPORT: 1.888.678.9427

WEB Management

Attention:  While installing and upgrading firmware, please remove physical loop connection first. 

DO NOT power off equipment while the firmware is upgrading!

Configuration by Web Browser

This section details configuration through the Web browser.

About Web-based Management

An embedded HTML web site resides in the flash memory on the CPU board. It contains 
advanced management features and allows you to manage the switch from anywhere on the 
network through a standard web browser such as Microsoft Internet Explorer.

The Web-Based Management function supports Internet Explorer 5.0 or later. It is based on Java 
Applets with an aim to reduce network bandwidth consumption, enhance access speed and 
present an easy viewing screen.

Note:  By default, IE5.0 or later version does not allow Java Applets to open sockets. You need to 

explicitly modify the browser setting in order to enable Java Applets to use network ports.

Summary of Contents for CNGE2FE8MSPOE2










































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands