manualshive.com logo in svg

Comnet CNGE2FE8MSPOE2, Installation And Operation Manual

Share
Download
Comnet CNGE2FE8MSPOE2 Installation And Operation Manual Download Page 20

INS_CNGE2FE8MSPOE2_REV–

12/20/12     PAGE 20

INSTALLATION AND OPERATION MANUAL 

CNGE2FE8MSPOE2

TECH SUPPORT: 1.888.678.9427

SFP

The switch has fiber optic ports with SFP connectors. The fiber optical ports are available with 
multi-mode and single-mode fiber with various distance and connector types. Please remember 
that the TX port of Switch A should be connected to the RX port of Switch B.

Switch-A                                                     Switch-B

Console Port Cable

CNGE2FE8MSPOE2 switches can be managed by the console port. The DB-9 to RJ-45 cable can 
be found in the package. You can connect them to the PC via a RS-232 cable with DB-9 female 
connector and the other end (RJ-45 connector) connects to console port of switch.

PC pin 

out (male) 

assignment

RS-232 with 

DB9 female 

connector

DB9 to RJ 45

Pin #2 RD

Pin #2 TD

Pin #2

Pin #3 TD

Pin #3 RD

Pin #3

Pin #5 GD

Pin #5 GD

Pin #5

Summary of Contents for CNGE2FE8MSPOE2










































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands