Comnet CNGE2FE8MSPOE2 Installation And Operation Manual Download Page 8

Page: 8 / 105

INS_CNGE2FE8MSPOE2_REV–

12/20/12 PAGE 8

INSTALLATION AND OPERATION MANUAL

CNGE2FE8MSPOE2

TECH SUPPORT: 1.888.678.9427

Software Features

World’s fastest Redundant Ethernet Ring: C-Ring (Recovery time <10ms over 250 units
connection)

Supports Ring Coupling, Dual Homing over C-Ring

Supports SNMPv1/v2/v3 & RMON & Port base/802.1Q VLAN Network Management

Event notification by Email, SNMP trap and Relay Output

Web-based, Telnet, Console, CLI configuration

Enable/disable ports, MAC based port security

Port based network access control (802.1x)

VLAN (802.1Q) to segregate and secure network traffic

Radius centralized password management

SNMPv3 encrypted authentication and access security

RSTP (802.1w)

Quality of Service (802.1p) for real-time traffic

VLAN (802.1Q) with double tagging and GVRP supported

IGMP Snooping for multicast filtering

Port configuration, status, statistics, mirroring, security

Remote Monitoring (RMON)

Summary of Contents for CNGE2FE8MSPOE2










































































































Search results

Summary of Contents for CNGE2FE8MSPOE2

Reviews:

Brands by name

Popular brands

Comnet CNGE2FE8MSPOE2, Installation And Operation Manual

Search results

Summary of Contents for CNGE2FE8MSPOE2

Reviews:

Brands by name

Popular brands