1/2/02
ALA550
14
The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle
normally.
OVERRIDES THE ALARM WITH PASSWORD PIN CODE:
(
Alarm Feature
IV
-
3
Programming
)
Unlike valet switch easily found, and defeated, this security system allows the consumer to program a
password pin code. Offering a higher level of security.
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Within 5 seconds, enter your chosen the first digit code by press and release the Valet Switch.
(When finished above procedures, system's siren stop alarming, parking light stop flashing, other
sensor stop trigger, but the vehicle can not be start and drive away.)
3. Within 15 seconds of the last enter (the 1 st digit code), turn the Ignition Switch “OFF” then “ON”.
4. Within 15 seconds, enter your chosen the second digit code by press and release the Valet Switch.
5. Turn the ignition switch “OFF” position.
[4] Chirps form siren/horn, [3] flash from parking light to indicate the system was disarmed.
Note 1: You must override the alarm within 60 seconds. If not, the system will automatically re-arm.
EXAMPLE: To Override The System With The Password Code 83, you would;
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Within 5 seconds, Press and Release the Valet Switch 8 times
(When finished above procedures, system's siren stops alarming, parking light stop flashing, other
sensor
stop trigger, but the vehicle can not be start and drive away.)
3. Within 15 seconds of the last enter (the 1st digit code), turn the Ignition Switch “Off” then “ON”.
4. Within 15 seconds, Press and Release the Valet Switch 3 times
5. Turn the Ignition Switch to “Off” position.
[4] Chirps form siren/horn, [3] flash from parking light to indicate the system was disarmed.
J. VALET MODE:
(System in Disarm or Valet mode)
The valet switch allow you to temporarily bypass all alarm function, eliminating the need to hand your
transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm
function are bypassed, however the remote panic feature and remote door lock will remain operational.
To use the valet mode, the system must first be disarmed either by using you remote transmitter, or by
operating the
Manual override sequence.
Enter Valet Mode:
1. From the disarmed condition, turn the ignition to “ON” position.
2. Push and hold valet switch for 2 seconds until the LED turn on. The LED will remain on as long as the
system is in 'valet mode'.
Exit Valet Mode:
1. Return to normal operation, turn ignition 'on'.
2. Push and hold valet switch for 2 seconds, The LED will turn off indicate the system are exiting the valet
mode.
K. CAR LOCATOR
(See Feature
III – 4
Programming)
Press the
button
on the transmitter to active car locator function. (Factory Default setting )
Under Armed mode, press the
button
on the transmitter to active car locator function. (If you Program
button = Channel 3 Function)
The siren will chirp 6 times. The parking light will flash 12 times, for you to easily locate your car.
L. PANIC FUNCTION:
(See Feature
III – 4
Programming)
The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency.
1. Press and hold the
button or
button on the transmitter for 3 seconds. The alarm will
immediately sound. (Factory Default setting )
2. During panic mode, the normal function of this transmitter button will be suspended. The
and
buttons can be used to lock and unlock the doors (if the option is installed), however once the
button is pressed, the vehicle’s starter disable device, (where installed) will be enable allowing the
vehicle to start.
