1/2/02
ALA550
10
So the same thing applies in door/window sensor, (A device to detect door/window open.) you may put the
sensor to the garage door or window. If system armed, a person opens the door or window, the siren will
alarm.
Set the PIR and door/window sensor the same code if you use both of them.
Enter:
4. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
5. Push the Valet switch
8
times and hold it until
four
chirps and a long chirp is hearing then release the
valet switch. You are now in the Alarm feature
‘IV’
programming mode.
Program:
1. Press and release the transmitter
button once, [2] LED flash, [2] siren/horn chirp to indicate your are
in features “Sensor Programming mode”.
2. Activate the sensor to let the system program it's code. [2] Chirps to confirm programmed. (Only one code
could be program)
Delete:
Within 15 seconds, Again press and hold the transmitter
button for 4 seconds. One chirp to confirm
deleted the sensor code.
Password Pin Code Setup:
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch
8
times and hold it until
four
chirps and a long chirp is hearing then release the
valet switch. You are now in the Alarm feature
‘IV’
programming mode. You can program or delete the
password pin code as below:
Program:
1. Press and release the transmitter
button once, [2] LED flash, [2] siren/horn chirp to indicate your are
in features “Password Pin Code Programming mode”.
2. Within 5 seconds, begin to enter your chosen first 10ths digit by pressing and releasing the valet Switch
from 1 – 9 times.
3. Within 15 seconds of the last enter (the 1
st digit code), turn the Ignition switch to “ON” position.
4. Within 15 seconds, enter your chosen the second digit code by pressing and releasing the valet Switch
from 1 – 9 times.
5. Finish by turning the ignition switch to “OFF” position.
If the new password code was accepted, the unit would report back the newly entered code, by flashing the
LED, first indicating the first digit code has been memorized, pause and then the second digit code. The unit
will report the new code three times with a one-second’s pause between each code.
Note: If 15 seconds of inactivity expire, or if the ignition switch is turned “ON” for more then 5 seconds during
of above steps, the unit will revert back to the last successfully stored code. A [3] long chirps to confirm exit.
Will revert back to the last successfully stored code
Delete Password Pin Code / Override Without Password Pin Code (Factory default setting):
Within 15 seconds, press and hold
the
transmitter
button for 4 seconds. A one chirps to confirm
Deleted the Password Pin Code.
Example: To program the Password Code 92, you would;
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch
8
times and hold it until
four
chirps and a long chirp is hearing then release the
valet switch. You are now in the Alarm feature
‘IV’
programming mode.
Program:
1. Press and release the transmitter
button once, [2] LED flash, [2] siren/horn chirp to indicate your are
in features “Password pin code programming mode”.
2. Within 5 seconds, press and release the valet Switch 9 times.
3. Within 15 seconds of the last enter (the 1
st digit code), Turn the Ignition Switch to “ON” position.
4. Within 15 seconds press the valet Switch twice.
5. Turn the Ignition Switch to “OFF’ position.
You will note the LED flashing nine times, pause and then flash two times, pause. This pattern will be
repeated three times indicating the new code (92) has been accepted and stored in memory.
Test Mode
