COMESTERO GROUP
M21/03.02
Rev.02
of 25/09/03
Page 26 of 34
R
R
M
M
5
5
X
X
3
3
C
C
:
:
P
P
R
R
O
O
G
G
R
R
E
E
S
S
S
S
I
I
V
V
E
E
T
T
I
I
M
M
E
E
R
R
W
W
I
I
T
T
H
H
C
C
O
O
U
U
N
N
T
T
E
E
R
R
O
O
U
U
T
T
P
P
U
U
T
T
The only difference with RM5 x 30 version is that, in addition to the timed signal, the validator can
be directly connected to an electromechanical counter which will store the validator accounting
expressed as multiple of the basic value set on the validator.
PIN OUT OF RM5 X 3C VALIDATOR 10 PIN CONNECTOR
Pin No.
Meaning
Pin No.
Meaning
1
Gnd
6
Time inhibition/stop
2
+12-24 Vdc
7
Display Clock
3
Display Data
8
Timed output
4
Display Enable
9
Counter output
5
N.U.
10
N.U.
8
8
.
.
1
1
1
1
O
O
N
N
R
R
E
E
Q
Q
U
U
E
E
S
S
T
T
C
C
R
R
E
E
D
D
I
I
T
T
E
E
M
M
I
I
S
S
S
S
I
I
O
O
N
N
T
T
O
O
T
T
A
A
L
L
I
I
Z
Z
E
E
R
R
C
C
O
O
N
N
F
F
I
I
G
G
U
U
R
R
A
A
T
T
I
I
O
O
N
N
(
(
R
R
M
M
5
5
X
X
4
4
0
0
)
)
It recognizes 59 coins that can have even 59 different values, it sums them up;when the validator
has acquired a value equal to the credit cost, it accumulates it and the signal is given only on
request of the player who sends a credit to the machine by pressing a button.
This validator has been designed to meet the requirements of the manufacturers of Kiddy rides,
billiards, table games In general.
The signal can be of two types:
-
Adjustable pulse between 10msec and 2 sec (standard 100 msec (+0-2%)
-
Fixed awaiting a reset on PIN 6
NOTE:
When a value ranging between 10 and 630 msec is set, the ratio 1 to 4 is guaranteed,
i.e.the pulse will be active (low) for the fixed timed, while the pause time between one pulse and
the other will be four times as much. When a value higher than 630 msec is set, the pause time will
not follow this rule.
The fixed signal is useful when an automatism not equipped with self-supply must be supplied and
at the end of the cyle a reset signal will return.
The validator directly controls a display that visualizes the introduced amounts until the value of
one credit is reached and then the accumulated credits will be displayed.
Alternatively, i.e. when the use of a display is not provided, the presence of credits can be shown
using the signal given by the validator on output on pin 10 which is kept enabled when the validator
has at least 1 credit stored.
Also this version has an output for the direct control of an external counter of accepted coins.
By means of the portable programmer the following operations can be carried out:
-
Setting the cost of the single credit and the two bonus thresholds
-
Enabling and reading the internal counter of accepted coins
-
Selecting the type of signal: pulse or fixed (standard pulse)
-
Adjusting the length between 10msec and 2 sec in the case of a pulse
-
Individual disabling of coin acceptance channels
