7596004CM - Manuale EASYBLUE COMENDA ENG ok
- 10 -
3 INSTALLATION
EASY:BLUE installation must be done in a fresh, dry and good aerated place.
ATTENTION
EASY:BLUE must be installed by
qualified personnel and in compliance with
regulations
, there must be a tap above (to exclude the equipment from the water system
in case of maintenance interventions), a non-return valve, water sampling points
upstream and downstream of the device and a socket.
Avoid subjecting the machine to excessive temperature changes that could cause
condensation inside, which can damage the electronic parts.
Make sure the air vents are never blocked in order to not compromise motor cooling.
Instructions and representations that follow are to be considered for typical installations,
the specific components may vary depending on the accessories that accompany the
machine and derivation and delivery taps chosen.
CONTROLS TO BE CARRIED OUT BEFORE INSTALLATION
Presence and efficiency of grounding of power line.
Compatibility of the power line with the electrical specifications indicated on the plate
on the back of machine.
Electric cables of the power source circuit of upper than 0.75mm section.
Stability of the network tension (sudden changes in tension of less than 10%).
N°
DESCRIPTION
GENERAL SCHEMATIC REPRESENTATION
1
ENTRY
Rev/Rev
Descrizione Modifiche/Change description
Emissione/Emission
Approvato/Approval
-
-
Il presente disegno non può essere utilizzato né riprodotto o reso noto a terzi senza autorizzazione della
Think Water
This draw cannot be used nor reproduced or given to third parts without the authorisation from
Think Water
Scala/Scale
Tolleraza Generale/
General Tollerance
Denominazione/Product name
Progettista/Designer
Verifica/Confirm
Codice prodotto/ Product code
Applicazione/Application
N° disegno/N°drawing
• Esecutivo/
Executive
• Sperimentale/
Experimental
Data/Date
N° tavola/N° table
Materiale/Material
1:2
-
2010
-
media
1 di 1
pavan
-
Raggi non quotati/
Rays not quoted
±0.05
da/from
0.5
fino a/to
3
D
e
s
ig
n
a
z
ion
e/
Sp
e
c
if
ic
a
tio
n
media
D
e
n
o
m
in
a
z
ion
e/
Na
m
e
f
fine
m
±0.2
±0.1
±0.1
±0.1
±0.05
±0.3
±0.5
±0.15
±0.2
±0.8
±1.2
±0.3
±0.5
da/from
0.5
fino a /to
3
±0.2
1)
±0.5
±1
1) Per le dimensioni nominali minori di 0.5 [mm], gli scostamenti devono essere indicati vicino alle dimensioni nominali
1) If the nominal dimension is less 0.5 [mm] the limit of tollerance must be written near the nominal dimension
Classe di tolleranza/
Tolerance class
Tab. 1: Scostamenti limite [mm] ammessi per dimensioni lineari,
esclusi smussi e raccordi per eliminazione di spigoli (vedi Tab. 2)/
Limit of tolerance [mm] for linear dimension, without groove and
half-round fillet to erase edge
1)
Tab. 3: Scostamenti limite per dimensioni
angolari in funzione dei campi di lunghezza
[mm] del lato più corto dell'angolo/ Limit of
tolerance for angle, reference to the shorter
side of the angle [mm]
±1°
±0°30'
±0°20'
±0°10'
±0°5'
da/from
3
fino a/to
6
da/from
6
fino a/to
30
da/from
30
fino a/to
120
da/from
120
fino a/to
400
da/from
400
fino a/to
1000
da/from
1000
fino a/to
2000
da/from
3
fino a /to
6
oltre/over
6
Tab. 2: Scostamenti limite [mm] per
smussi e raccordi per eliminazione di
spigoli/ Limit of tolerance [mm] for groove
and half-round fillet to erase edge
da/from
0
fino a /to
10
da/from
10
fino a /to
50
da/from
50
fino a /to
120
da/from
120
fino a /to
400
oltre/over
4000
-
-
-
-
-
-
-
-
-
-
-
-
-
-
A3
UNI EN ISO 22768
1
2
3
4
5
6
2
PERMEATE
3
ELECTRIC
CONNECTOR
4
MIX VALVE
5
SUPPORTING
PERMEATE
6
DRAIN OUTPUT