COMEM eSDB-10C, Instruction Manual

Page: 6 / 66

6
Installation
The operating and installation requirements described in this
manual must be strictly followed. If not, the device can be
damaged or a malfunction may occur. The unit must be mounted
level and upright. The unit and piping must be installed so the
oil is not able to enter the breather. Do not install in an enclosed
cabinet; proper ventilation is required.
CAUTION
Figure 5
Figure 9
Put the plane gasket between the two flanges.
CAUTION
eSDB10
First step: Remove the tape/plastic cap from the entry/
exit air zones. Fix the upper flange (Fig.4/A) on the flange
of the pipe from the conservator
(Fig.4/B) with four M12 screws (Fig.4/C).
Second step: Check the upper level (Fig.16/17/18), the
internal bubble must be inside the smallest black ring.
Third step: unscrew the bottom screw in the lower part of
the device (Fig.5/A) until the end of the screws working
range.
Fourth step: unscrew plug on the eSDB10. Depending on
the position of the main air breather (eSDB15, eSDB30)
unscrew the right plug (Fig.7/A) or left plug (Fig.7/B).
Unscrew the plug on the main air breather (Fig.8/A).
Connect a pipe between the two plugs (Fig.9). The plug
thread is M16x1.5.
Figure 6
Figure 7
Figure 8
Figure 4
The transformer manufacturer can choose whether to apply the
anti-vibration kit which is supplied with the eSDB depending on the
sturdiness of the support (fig.6/A).
NOTE
D
C
B
A
6 5 4 3 2 1 7 8
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
This document is issued by means of a computerized system. The digitally stored original is electronically approved. The approved document has a date entered in the `Approved'-field. A manual signature is not required.
DRAWING SHEET ISO 5457: 1999-A3T
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly fobidden.
1/1 3
A
Development
NE-286
SHEET ITER REV STATUS DOCUMENT ID
ITABB-9AAE306693
- RESPONSIBLE DEPARTMENT
CONNECTION ESDB10
COMEM
TITLE / SUPPLEMENTARY TITLE COMPANY
Component Drawing -
PROJECT ID WORK ORDER ID BASED ON DOC ID DOCUMENT KIND APPROVED ON
- - Diego Boro
APPROVED BY REVIEWED BY CREATED BY
© COPYRIGHT ALL RIGHTS RESERVED
LAST REVISION
DESCRIPTION
AGGIORNATO DISEGNO - Drawing updated REPLACED
REVISION
TOLLERANZE GENERALI SECONDO - GENERAL TOLERANCES ACCORDING TO ISO 2768
m
SCALE NO
MATERIAL WEIGHT - kg
- - - -
PROCESS PART NUMBER
- - -
M16x1.5 PLUG
M16x1.5 PLUG
D
C
B
A
6 5 4 3 2 1 7 8
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
This document is issued by means of a computerized system. The digitally stored original is electronically approved. The approved document has a date entered in the `Approved'-field. A manual signature is not required.
DRAWING SHEET ISO 5457: 1999-A3T
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly fobidden.
1/1 2
A
Development
NE-1188
SHEET ITER REV STATUS DOCUMENT ID
ITABB-9AAE306693
- RESPONSIBLE DEPARTMENT
COMEM ESDB10
COMEM
TITLE / SUPPLEMENTARY TITLE COMPANY
Component Drawing -
PROJECT ID WORK ORDER ID BASED ON DOC ID DOCUMENT KIND APPROVED ON
- - Diego Boro
APPROVED BY REVIEWED BY CREATED BY
© COPYRIGHT ALL RIGHTS RESERVED
A
D
C
B
A
6 5 4 3 2 1 7 8
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
This document is issued by means of a computerized system. The digitally stored original is electronically approved. The approved document has a date entered in the `Approved'-field. A manual signature is not required.
DRAWING SHEET ISO 5457: 1999-A3T
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly fobidden.
1/1 2
A
Development
NE-1188
SHEET ITER REV STATUS DOCUMENT ID
ITABB-9AAE306693
-
RESPONSIBLE DEPARTMENT
COMEM ESDB10
COMEM
TITLE / SUPPLEMENTARY TITLE COMPANY
Component Drawing -
PROJECT ID WORK ORDER ID BASED ON DOC ID DOCUMENT KIND APPROVED ON
- - Diego Boro
APPROVED BY REVIEWED BY CREATED BY
© COPYRIGHT ALL RIGHTS RESERVED
B
A
C
D
C
B
A
6 5 4 3 2 1 7 8
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
This document is issued by means of a computerized system. The digitally stored original is electronically approved. The approved document has a date entered in the `Approved'-field. A manual signature is not required.
DRAWING SHEET ISO 5457: 1999-A3T
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly fobidden.
1/1 2
A
Development
NE-1188
SHEET ITER REV STATUS DOCUMENT ID
ITABB-9AAE306693
-
RESPONSIBLE DEPARTMENT
COMEM ESDB10
COMEM
TITLE / SUPPLEMENTARY TITLE COMPANY
Component Drawing -
PROJECT ID WORK ORDER ID BASED ON DOC ID DOCUMENT KIND APPROVED ON
- - Diego Boro
APPROVED BY REVIEWED BY CREATED BY
© COPYRIGHT ALL RIGHTS RESERVED
A B
D
C
B
A
6 5 4 3 2 1 7 8
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
This document is issued by means of a computerized system. The digitally stored original is electronically approved. The approved document has a date entered in the `Approved'-field. A manual signature is not required.
DRAWING SHEET ISO 5457: 1999-A3T
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly fobidden.
1/1 2
A
Development
NE-1188
SHEET ITER REV STATUS DOCUMENT ID
ITABB-9AAE306693
- RESPONSIBLE DEPARTMENT
COMEM ESDB10
COMEM
TITLE / SUPPLEMENTARY TITLE COMPANY
Component Drawing -
PROJECT ID WORK ORDER ID BASED ON DOC ID DOCUMENT KIND APPROVED ON
- - Diego Boro
APPROVED BY REVIEWED BY CREATED BY
© COPYRIGHT ALL RIGHTS RESERVED
A
D
C
B
A
6 5 4 3 2 1 7 8
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
This document is issued by means of a computerized system. The digitally stored original is electronically approved. The approved document has a date entered in the `Approved'-field. A manual signature is not required.
DRAWING SHEET ISO 5457: 1999-A3T
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly fobidden.
1/1 2
A
Development
NE-1188 SHEET ITER REV STATUS DOCUMENT ID
ITABB-9AAE306693
- RESPONSIBLE DEPARTMENT
COMEM ESDB10
COMEM
TITLE / SUPPLEMENTARY TITLE COMPANY
Component Drawing -
PROJECT ID WORK ORDER ID BASED ON DOC ID DOCUMENT KIND APPROVED ON
- - Diego Boro
APPROVED BY REVIEWED BY CREATED BY
© COPYRIGHT ALL RIGHTS RESERVED
A
SELF-DEHYDRATING BREATHERS eSDB 10/15/30