COMEM eSDB-10C, Instruction Manual

Page: 51 / 66

51
Figure 11
Placer le joint d'étanchéité entre les deux brides.
PRUDENCE
eSDB-15/30
Première étape : Retirez le ruban ou le capuchon en
plastique des zones d'entrée et de sortie d'air.
Fixez la bride supérieure (Fig. 10/A) sur la bride du tuyau
provenant du conservateur (Fig. 10/B) à l'aide de quatre
vis M12 (Fig. 10/C).
Deuxième étape : Vérifiez le niveau supérieur (Fig.16/17/
18) ; la bulle interne doit se trouver à l'intérieur de la plus
petite bague noire.
Troisième étape : dévissez la vis inférieure dans la partie
inférieure du dispositif (Fig. 11/A) jusqu'à la fin de la plage
de fonctionnement des vis.
Figure 12
Figure 10
Le fabricant du transformateur peut choisir d'appliquer le kit
anti-vibration fourni avec l'eSDB en fonction de la robustesse
du support (Fig. 12/A). Pour les raccordements électriques,
COMEM conseille d'utiliser des câbles armés.
REMARQUE
Entre le bouchon et le boîtier, un joint OR doit être placé pour
éviter toute fuite.
Le système (tuyau et bouchon) doit être assemblé pour garantir
l'étanchéité.
AVERTISSEMENT
Figure 9
Raccordez un tuyau entre les deux bouchons (Fig. 9).
Le filetage est M16x1,5.
D
C
B
A
6 5 4 3 2 1 7 8
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
This document is issued by means of a computerized system. The digitally stored original is electronically approved. The approved document has a date entered in the `Approved'-field. A manual signature is not required.
DRAWING SHEET ISO 5457: 1999-A3T
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly fobidden.
1/1 3
A
Development
NE-286 SHEET ITER REV STATUS DOCUMENT ID
ITABB-9AAE306693
- RESPONSIBLE DEPARTMENT
CONNECTION ESDB10
COMEM
TITLE / SUPPLEMENTARY TITLE COMPANY
Component Drawing -
PROJECT ID WORK ORDER ID BASED ON DOC ID DOCUMENT KIND APPROVED ON
- - Diego Boro
APPROVED BY REVIEWED BY CREATED BY
© COPYRIGHT ALL RIGHTS RESERVED
LAST REVISION
DESCRIPTION
AGGIORNATO DISEGNO - Drawing updated REPLACED
REVISION
TOLLERANZE GENERALI SECONDO - GENERAL TOLERANCES ACCORDING TO ISO 2768 m SCALE NO
MATERIAL WEIGHT - kg
- - -
-
PROCESS PART NUMBER
- - -
M16x1.5 PLUG
M16x1.5 PLUG
D
C
B
A
6 5 4 3 2 1 7 8
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
This document is issued by means of a computerized system. The digitally stored original is electronically approved. The approved document has a date entered in the `Approved'-field. A manual signature is not required.
DRAWING SHEET ISO 5457: 1999-A3T
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly fobidden.
1/1 2
A
Development
NE-1188
SHEET ITER REV STATUS DOCUMENT ID
ITABB-9AAE306693
-
RESPONSIBLE DEPARTMENT
COMEM ESDB10
COMEM
TITLE / SUPPLEMENTARY TITLE COMPANY
Component Drawing -
PROJECT ID WORK ORDER ID BASED ON DOC ID DOCUMENT KIND APPROVED ON
- - Diego Boro
APPROVED BY REVIEWED BY CREATED BY
© COPYRIGHT ALL RIGHTS RESERVED
A
D
C
B
A
6 5 4 3 2 1 7 8
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
This document is issued by means of a computerized system. The digitally stored original is electronically approved. The approved document has a date entered in the `Approved'-field. A manual signature is not required.
DRAWING SHEET ISO 5457: 1999-A3T
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly fobidden.
1/1 2
A
Development
NE-1188
SHEET ITER REV STATUS DOCUMENT ID
ITABB-9AAE306693
-
RESPONSIBLE DEPARTMENT
COMEM ESDB10
COMEM
TITLE / SUPPLEMENTARY TITLE COMPANY
Component Drawing -
PROJECT ID WORK ORDER ID BASED ON DOC ID DOCUMENT KIND APPROVED ON
- - Diego Boro
APPROVED BY REVIEWED BY CREATED BY
© COPYRIGHT ALL RIGHTS RESERVED
B
A
C
D
C
B
A
6 5 4 3 2 1 7 8
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
This document is issued by means of a computerized system. The digitally stored original is electronically approved. The approved document has a date entered in the `Approved'-field. A manual signature is not required.
DRAWING SHEET ISO 5457: 1999-A3T
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly fobidden.
1/1 2
A
Development
NE-1188
SHEET ITER REV STATUS DOCUMENT ID
ITABB-9AAE306693
- RESPONSIBLE DEPARTMENT
COMEM ESDB10
COMEM
TITLE / SUPPLEMENTARY TITLE COMPANY
Component Drawing -
PROJECT ID WORK ORDER ID BASED ON DOC ID DOCUMENT KIND APPROVED ON
- - Diego Boro
APPROVED BY REVIEWED BY CREATED BY
© COPYRIGHT ALL RIGHTS RESERVED
A