Comdial DSU II Series User Manual Download Page 66

Page: 66 / 106

Default Volume Control

When you change and save the volume, that change remains in effect until you
change it again (referred to as default setting).

Set the speaker, headset, handset, or
group listening loudness for all future
calls using the following steps:

1. PRESS

INTERCOM

2. CHOOSE speaker, headset, handset, or

group listen mode to be affected.

3. While in that mode, PRESS

VOLUME UP

VOLUME DOWN

to adjust loudness.

4. DIAL

**5

to hold the loudness at

the last setting for all future calls (until it
is changed again).

5. REPEAT this procedure in each mode until all default volume

levels have been properly set.

NOTE: You may adjust the volume of a call in any mode (over speaker, headset,

handset or group listen), at any time during the call, by pressing

VOLUME UP

VOLUME DOWN

. When the call ends, the volume of all future calls is reset to the

programmed (default) setting.

LCD Speakerphone Station User’s Guide

Other Features

GCA70-281

Impact SCS Volume Buttons

Impact Volume Buttons

Summary of Contents for DSU II Series











































































































Search results

Summary of Contents for DSU II Series

Reviews:

Related manuals for DSU II Series

Brands by name

Popular brands

Comdial DSU II Series, User Manual

Search results

Summary of Contents for DSU II Series

Reviews:

Related manuals for DSU II Series

Brands by name

Popular brands