Coltene BioSonic UC125, Owner'S Manual

Page: 5 / 60

Owner’s Guide
5
bottom of basket. Place basket in
tank and clean for desired time.
C. Beaker Holder
Place three UC153 Beaker Holders
on the bezel. Place positioning rings
around the beaker so that the bottom
2/3 of the beaker is suspended in the
main bath. Clean for desired time.
IX. Environmental Conditions
• Intended for indoor use.
• Maximum altitude 2000 m.
• Temperature range 5°C to 40°C
(41°F to 104°F).
• Maximum relative humidity 80% for
temperatures up to 31°C (88°F),
decreasing linearly to 50% relative
humidity at 40°C (104°F).
• Main supply voltage fluctuations not
to exceed ± 10% of the nominal
voltage.
• Transient over voltages category II.
• Pollution degree 2.
• Class I equipment.
X. Warnings
• Do not operate the unit without
sufficient solution in the tank.
• Do not use water alone as the
carrier bath. Water is not a
satisfactory coupling agent unless a
wetting agent is used. For best
results use BioSonic General
Purpose, BioSonic Germicidal
Cleaner or BioSonic Enzymatic
Ultrasonic Cleaning solutions.
• Do not place objects directly on
bottom of the tank because they
may block cavitation and cause
buildup of heat in the transducer
causing premature failure. Use only
BioSonic UC125 accessory baskets,
cassette racks or beakers to hold
items.
• Do not use flammable liquids with
BioSonic units.
• Do not restrict airflow. Provide
adequate ventilation by maintaining
at least 2 inches clearance at
the back.
• Do not use acids in the stainless
steel tank.
• Do not subject unit to shock or
impact.
• Do not immerse the unit in water.
• Keep unit covered to reduce
airborne contaminants.
• This product is intended for use only
by trained healthcare professionals.
• Use this product in accordance with
the instructions in the owner’s guide.
• Unspecified or improper use of this
product may impair safety protection.
• Do not place fingers or hands in the
ultrasonic tank while in operation.
• Before cleaning items of
considerable value ultrasonically,
consult the item’s manufacturer for
cleaning precautions.
• Use only the supplied power cord or
equivalent.
• The power off selection from the
keypad does not turn off main power
to the unit.
• Operation for long periods of time
will cause the cleaning solution to
get very hot. To avoid scalding, do
not place hands in the solution or
spill any onto you. Be careful when
removing an item from the tank as it
may also be hot.
• Do not disassemble the unit. There
are no user serviceable parts inside.
• Never drain tank by manually
discarding solution as this may
cause the unit to stop working
properly.
XI. Order Information
Cat.No Description Qty
Unit and accessories:
UC125 100 Unit (100V, 50/60 Hz) 1
115 Unit (115V, 50/60 Hz) 1
230CE Unit (230V, 50/60 Hz) 1
230UK Unit (230V, 50/60 Hz) 1
240 Unit (240V, 50/60 Hz) 1
UC155XD Accessory Kit
3/4 FingerGuard Basket, (2) Beakers,
(2) Covers, (2) Positioning Rings and
(2) Beaker Holders
UC151XD Full Size FingerGuard Basket 1
UC152XD 3/4 FingerGuard Basket 1
UC153 One Beaker Holder 1
UC350 Replacement Drain Filters 3
UC360 Replacement Drain Hose 1
UC53 600 ml Beaker with Cover and
Positioning Ring
1
Tank Solutions:
UC30 General Purpose Cleaning Solution
Concentrate in MeterDose
®
Dispensing Bottle (16 oz.) 473 ml
UC32 Enzymatic Ultrasonic Cleaner
Concentrate in MeterDose
Dispensing Bottle (8 oz.)
236 ml
UC34 Plaster & Stone Remover
Powder Concentrate in
Jar (1.85 lbs.)
840 g
UC38 Germicidal Ultrasonic Cleaning
Concentrate in MeterDose
Dispensing Bottle (8 oz.)
236 ml
UC39 Cement Remover Concentrate
in MeterDose Dispensing
Bottle (16 oz.)
473 ml
UC42 Germicidal Ultrasonic Cleaning
Concentrate in MeterDose
Dispensing Bottle (16 oz.)
473 ml
XII. Maintenance
A. Cleaning
All components should be cleaned
each day by wiping with a soft cloth
moistened with a commercially
available mineral deposit remover
followed by cleaning with isopropyl
alcohol or a mild disinfectant.
CAUTION:
Do not use petroleum based
solvents, iodophors or phenolic based
products. (Iodophors and phenolics can
stain the surface of the unit.) Clean up all
liquid spills immediately. Rust deposits
on tank can be cleaned/removed with a
commercially available stainless steel
cleaner.
B. Inspecting the Power Cord
Periodically check the power cord for
damage and see that the connectors
at both ends of the cord are fully
seated.
C. Changing the Fuse
1. Remove the power cord from the
wall outlet first and then from the
power cord receptacle on the rear of
the unit.
2. The fuse compartment is located
directly next to the power cord
receptacle. To access, take a small,
flat-headed screwdriver to the tab on
the fuse holder. Apply slight pressure
to release the fuse holder (
Fig. 12 ).
3. Gently remove the fuse from the
fuse holder.
4. Examine the fuse ( Fig. 13 ). If blown,
replace with a fuse that matches the
unit’s voltage and current (see
section XIII). If fuse appears to be in
good condition return the unit to your
dealer or Coltène/Whaledent.