Colorjet VerveLED VLY 2513 Installation And Troubleshoot Manual Download Page 50

Page: 50 / 56

Page | 49

VERVE LED

18. Troubleshooting

1. “Printer Not Initializing”

Problematic Parts

Reasons

Correction Steps

Emergency Switch

Switch is Pressed

Release the Emergency Switch

220V AC

No power supply to the Head
Board

Check the Input/output Volt
Check MCB and ON it, if not

24 VDC

No power to SMPS output

Check SMPS Output Power
Check  24  V  power  supply  and
replace  the  Power  Supply,  if
faulty
Check  the  24  V  Power  Supply
cable and replace it, if required

Servo Driver

Error in display
No power to Servo Motor

Check and try to resolve the
error on the display screen
Check the power connection
and replace it, if faulty

Main Board

Factory settings are disturbed
Fault in Main Board

Correct the factory settings
Replace the Main Board, if
faulty

Head Board

Fault in Head Board

Replace the Head Board, if
faulty

Encoder Sensor

Fault in Encoder Sensor

Replace the Encoder Sensor.

2. “Printer Manager Not Showing “Ready”

Problematic Parts

Reasons

Correction Steps

USB Driver

Driver is not installed

Install the printer driver, if not
installed

(Refer

the

Installation of Printer Manager
section)

USB Cable

USB Cable is loosely connected
to the printer
USB Cable is faulty

Check and tighten the USB cable
Replace it, if faulty

Printer Not Initialized

Refer to Printer Not Initialized
Section

Summary of Contents for VerveLED VLY 2513

























































Search results

Summary of Contents for VerveLED VLY 2513

Reviews:

Related manuals for VerveLED VLY 2513

Brands by name

Popular brands

Colorjet VerveLED VLY 2513, Installation And Troubleshoot Manual

Search results

Summary of Contents for VerveLED VLY 2513

Reviews:

Related manuals for VerveLED VLY 2513

Brands by name

Popular brands