background image

34

2012 Audiovox Electronics Corporation. All rights reserved.

5 - Siren / Horn: 

This feature selects which output(s) will sound the system’s arm/

disarm chirps. This feature does not effect the triggered state of the security
system and during a triggered cycle, both the siren and horn outputs will activate
respectively.

6 - Custom Code: 

This feature determines the manor in which the security system

can be overridden in the event the transmitters are lost or damaged. Refer to
Custom PIN Code programming.

OFF - Standard valet button override.
ON - Requires entry of user selected PIN code.

7 - Siren Duration: 

Select between a 30 or 60 second siren duration when the

security system is triggered.

8 - 3 Zone Shock: 

The 3 Zone setting is for 2 Way systems only.

2 Zones - Standard light touch and full trigger notifications.
3 Zones - Upon a light touch impact, the system will remain silent and only
notify the 2 way transmitter, if a second impact is detected within 5 minutes
a normal light touch notification will sound from the vehicle. Full trigger
impacts remain in effect at all times regardless of selection.

9 - Security: 

Controls security functionality - ON / OFF.

ON - Full security functionality.
OFF - The security system does not trigger. Panic and all other convenience

features operate as normal.

10 - 2 Way Communication: 

Controls communication between the control module

and the 2 way transmitter. Communication between the control module and the 1
way transmitter is unaffected.

ON - The 2 way transmitter sends commands to the control module and

receives commands/notifications from the control module.

OFF - The 2 way transmitter sends commands to the control module.

Summary of Contents for Procomp













































Reviews: