Code Alarm Procomp Installation Manual Download Page 22 | Manualshive

Page: 22 / 44

background image

22

2012 Audiovox Electronics Corporation. All rights reserved.

Negative Multiplexed and Negative Multiplexed with 2-step Unlock

All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /
unlock switch.

Verification:

This wire will show variable ground when the switch is activated.

Please consult the wire and location chart for specific resistor values for
your vehicle.

Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator
inside the driver’s door.

Verification:

This wire will rest at ground and register positive voltage when

the driver’s door is unlocked.

Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram
below using (2) SPDT relays (not supplied).

NOTE:

When adding the 2 step unlock feature the BLUE/GREEN 2nd door unlock

wire will be used to unlock all vehicle doors on the second press of unlock. An
additional SPDT relay (not supplied) is required. Connect the relay as shown in
the diagram below to unlock the driver’s door on the first press of unlock.

Lock

Unlock

87

87a

86

85

30

Vehicle Door Lock
Control Relays

GREEN (-) Lock Output

BLUE (-) Unlock Output or
BLUE/GREEN 2nd Unlock
Output for 2 Step Unlock

For 2 Step Unlock:

Fused +12 Volt
Battery Souce

BLUE (-) Unlock Output

From Keyless Entry
Module or Door
Unlock Relay

Drivers Door
Unlock Motor Wire

X

Cut

Multiplex Locks:

87

87a

86

30

87

87a

86

30

85

85

Fused +12 Volt
Battery Source

Ground

Resistor

«
...
20
21
22
23
24
...
»

Summary of Contents for Procomp













































Reviews:

No comments

Related manuals for Procomp

Brand: LaserLine Pages: 20

Electronic Micro Alarm

Brand: Pacific GSM Pages: 4

Brand: jablotron Pages: 2

Brand: Kidde Pages: 2

Brand: Viper Pages: 42

Brand: Life Pages: 4

Brand: GST Pages: 2

Prestige APS-920

Brand: Audiovox Pages: 12

Platinum+ APS 687C

Brand: Audiovox Pages: 12

Brand: resideo Pages: 2

Brand: Oregon Scientific Pages: 12

Brand: VESDA Pages: 116

Brand: Naxa Pages: 10

Brand: IKEA Pages: 40

Brand: Code Alarm Pages: 12

Professional Series CA 1050

Brand: Code Alarm Pages: 20

Brand: Sparkrite Pages: 12

Brand: Viper Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands