background image

5

CA1B5 / AS9234E 4280844 Owners rev A.

 Timed Start Operation:

 

To begin the start timer, within 10 seconds of turning off the ignition switch, activate 

the RF command to start 2 times. (Press the start button four times). The lights 

will flash and the siren will chirp 4 times. Indicating timed interval mode has been 

initiated. The vehicle will automatically start every 2 or 4 hours as programmed. To 

cancel the timed start mode start the vehicle either by RF or by the ignition key.

 Remote Start Override Mode (Valet Mode) - AS9234E

  The intent of the remote start override / manual shut down circuit is to allow the 

vehicle operator to prevent operation of the Remote Start Unit regardless of the RF 

transmitter operation.

 

Enter Remote Start Override:

   

1.   With the system disarmed/unlocked, and the ignition switch off Press and  

 

 

Hold the PBLED push button switch (dash mounted).

   

2.  Turn the ignition switch on, off, on, off, on, off.

   

3.  The LED begins to flash two short flashes followed by one long flashes  

 

 

and continues this pattern until returned to normal mode of operation.

  The action above puts the unit into the Remote Start Override mode or vehicle service 

mode and will not start from the RF transmitter or any other input.

 

Exit Remote Start Override:

   

1.  With the system disarmed, Press and Hold the PBLED push button  

 

 

switch (dash mounted) on.

   

2.  Turn the ignition switch on, off, on, off, on, off.

   

3.  The LED turns off indicating that the R/S unit is fully functional one again.

Summary of Contents for CA1B5









Reviews: