background image

 

 pag 

22 

P01:  Manual AmbientSetPoint ( ManSet ) 
P02:  Manual or auto setpoint enabling ( ONSetMan ) 
P03:  manual or automatic mode change enabling ( ONModeMan ) 
P04:  humidity setpoint in the Cool mode ( SetURCool ) 
P05:  humidity setpoint in the Heat mode ( SetURHeat ) 
P06:  Outlet temperature Setpointin in Cool mode ( SetOutCool ) 
P07:  Outlet temperature Setpointin in Heat mode ( SetOutHeat ) 
P08:  NOT USED (The displayed value is in “ppm / 10”)   
P09:  setpoint positive/negative max. variation range by the user 
P10  thermostat temperature probe offset 
P11  thermostat humidity probe offset 
P12  Clivet Bus thermostat address 
 
By P09 the range within which the user can modify the machine set-point is defined. 

 

ALARM LIST 

BEFORE RESETTING AN ALARM, IDENTIFY AND REMOVE ITS CAUSE. 

REPEATED RESETS CAN CAUSE IRREVERSIBLE DAMAGE. 

 

The ALARMS indicate a potentially hazardous situation for the machine integrity.  
Before resetting the alarm, identify and remove the reason of the lock: a repeated reset can cause irreversible damage. That's 
why the reset is MANUAL, namely through keyboard (provided that the cause no longer exists). 

 

PRE-ALARMS and SIGNALS indicate a close risk situation. Their occurrence can be accepted if occasional and/or in 
temporary situations (for example at the system start-up).  
The reset is AUTOMATIC, that is there is a self-reset as soon as the cause ceases without any keyboard intervention.  

 

FAILURES signal the malfunctioning of probes and transducers; they are AUTOMATICALLY reset, so that anyway the unit can 
operate, even if possibly with reduced functions.  

 

In case of doubt contact an authorized service center. 

 

The presence of one or more alarms is signalled by the ALARM CODE blinking and by the machine time it/they occurred. 

 

The cumulative lock relay activates simultaneously with the alarm code displaying.  
Some alarms, typically PRE-ALARMS, do not activate the relay.  

 

The table shows all the variables which can be managed by the electronic system. 
According to the machine configuration and the accessories, some alarms can be not relevant. 

 

Code Meaning 

Reset 

E01 

Inlet temp. Probe fault  

Automatic – block only of the recovery compressor 

E02 

Outlet temp. Probe fault 

Automatic – blockout of the unit 

E03 

Externe temperature probe fault 

Automatic - block only of the recovery compressor 

E04 

Antifreeze probe fault 

Automatic – blockout of the unit 

E05 

Ambient UR% probe fault 

Automatic – humidity control block 

E06 

Externe UR% probe fault 

Automatic – the external UR is ignored 

E07 

Outlet UR% probe fault 

Automatic – humidity control block only in winter mode 

E08 

Air quality probe fault 

Automatic – inhibits air quality control 

E09 

Flow-rate transducer fault 

Automatic – exclusion only of the recovery compressor 

E10 

Water temperature probe fault 

Automatic – closing of the water valve and deactivation of the 
automatic change of the machine mode 

E11 

Fire alarm 

Manual  

E12 

Outlet – inlet fan protection intervention 

Manual - blockout of the unit 

E13 

Recovery compressor low pressure 

Automatic – recovery compressor block 

E14 

Recovery compressor high pressure 

Manual - recovery compressor block 

E15 

Recovery thermal compressor 

Manual - recovery compressor block 

E16 

Water coil antifreeze thermostat 

Manual - blockout of the unit 

E17 

Antifreeze alarm from water probe 

Manual - blockout of the unit 

E18 

Humidifier alarm 

Manual – winter humidification block 

E19 

Outlet 1 high temp. signaling Automatic 

 

E20 

Outlet 2 high temp. signaling 

Manual  

E21 

Outlet 1 low temp. signaling Automatic 

 

E22 

Outlet 2 low temp. signaling 

Manual  

Summary of Contents for CPAN-U-17













































Reviews: