C L I M A T E M A S T E R W A T E R - S O U R C E H E A T P U M P S
TSL Vertical Stack
R e v. : 0 4 / 2 4 / 2 0 1 9
20
C l i m a t e M a s t e r Wa t e r - S o u rc e H e a t P u m p s
G Style
Return Air Panel
6.00
(152)
Note 8, 9
DRYWALL
5/8"
(16)
CABINET
TOP VIEW
3-1/2
(89)
It is recommended to leave 2” (51) minimum clearance
on both sides for removing panel
X
Seal Gap (4) Sides
X
Frame
Outside
Drywall
C
57-1/2
(1460) R.O.
5-7/8*
(149)
Floor
12-1/4
(311)
28-5/8
(727)
(Order seperately) 48A0100N04 may be
installed on left or right side. Note 7
short wire harness to be installed in electric box,
remove ko in box cover, snap in molex.
D
59
(1599)
4.50* (114)
Front View
Frame Installed
G Panel
Perimete
4 Panel
Crossba
Lowest P
of Tabs
Third Pair
Tabs from
Mounting
Nuts (1/4-
* Dimension if cabinet is on floor.
Add if cabinet is on stand/pad.
9.00 x 2.00 KO (228 x 51)
Outside air opening,
left or right side
to suit installation.
“G” Frame
24.12
.38
(10)
(612)
4.75 (120)
Cross bars
R.O.
2
Frame
1
2
Cross Bar
1
2
Description
Kit Part
Qty
1
B
A
Cabinet
Flange
1.25 (32)
Frame
Crossbars
(Note 4)
X
X
FRONT VIEW
ѥ
NOTICE!
ѥ
Recessed cabinet requires frame kit.
Outside air requires motorized damper
Seal between the frame and cabinet with
weather seal material to avoid air being pulled
in from the wall cavity. Attach frame to studs
not cabinet.
Do not distort frame shim sides if required.
Notes
1. Cabinet con
Ƃ
guration will determine slab core drilling location and walls surrounding cabinet.
2. Recommend stud walls surrounding cabinet. Drywall and studs should not be attached or contacting cabinet for best
sound attenuation. Where possible
Ƃ
ll gaps with sound absorbing material. Use iso pad under cabinet. Secure cabinet t
ƃ
oor in two places at back.
3. Return air panel overlaps rough opening, allow minimum of 3 1/2" (89) dry wall to corner. Do not caulk panel to wall.
4. G Panel attaches to frame cross bars. Cabinet must be recessed behind wall.
5. Bend out 4 tabs per side on frame. Position cross bars behind ears, attach with 8 screws.
6. For
Ƃ
lter access, pivot inner panel, open
Ƃ
lter access snap. For chassis removal, remove G Panel, remove 2 cross bars,
remove
Ƃ
lter panel, slide out chassis.
7. When untreated outside air is required, 48A0100N04 motorized damper must be used, mixed air temperature
must be no lower than 45°F (7°C), no higher than 95 DB/75 WB, and not exceed 20% of total CFM. Contractor
must supply air duct, cut hole in stud, remove K.O., assemble and wire damper assembly.
Note: Use extreme weather temperatures.
8. For 2"
w
lter set cabinet 6.25" (158) from front of drywall.
or pre-treated air Above 45°F (7°C).
Note 5
Optional Damper Moto
r
48A0100N51
48A0100N
48A0100N52
19-5/8
(498)
16-5/8
(400)
19
(483)
17.00
(432)
24
(610)
19.25
(489)
17.00
(432)
24.25
(616)
24-3/8
(620)
15-18
09-12
24-36
Panel
C
B
A
Kit
Size
D
21.50
(546)
18.50
(470)
25.50
(648)
Frame Kit
Typical Cabinet with G Panel Installation - Flush Air Frame
