ClimAir Multi Therm-C Operating Instructions Manual Download Page 11

 

Room thermostat  MTC 

 

 

 

 

 

 

 

 

 

 

 11/12

 

 
Screen 6 
Shows  the  last  16  E  errors. These  errors  can reset  automaticly. 
The  blinking  nr  is  the  last  error.  The  CRC  code  is  the  software 
version in the heater. 
 
Screen 7 
Shows  the  last  16  A  errors.  These  errors  have  to  be  reset  by 
hand.  The  blinking  nr  is  the  last  error.  The  CRC  code  is  the 
software version in the heater. 

18  Installer menu 

Menu (M) 

installateur

PIN 0543

 

 
The functioning of the heater and the controller can be changed by changing the parameters in the 
installer menu. 
The following options are available 

  Heater modus (modulation from the heater) 

o

  Heater full (fully modulatin) (Default) 

o

   

Heater high (Only on high position) 

o

   

Heater mid (Only on middle position) 

o

   

Heater low(Only on low position) 

o

   

Heater low&mid (Low and middle position) 

o

   

Heater mid&high (Middle and high position) 

  deltaT hysterese 

o

  Hystt up  12°C (Value for switching the delta T ON) 

o

  Hyst down 8°C (value for swiching OFF) 

  Delta T2Hystereses (Not used) 

o

  Hyst up 4°C 

o

  Hyst down 2°C 

  Hystereses (computing value for thermostat) 

o

  0,3°C 

  I Factor (computing value for thermostat) 

o

  I  5min 

  Delta T2 regeling (not used) 

o

  ON / OFF 

  External sensor  

o

  ON /OFF / average 

  View mode Only 

o

  ON/OFF 

With this option the heat demand from the thermostat is disabeled. The 
thermostat can be uses as a remote status reader. To exit the view mode press 
the M button 10 seconds and enter the installer menu again. 

  External Input 

o

  Closed=Burn 

o

  Closed is OFF (standard) 

19  Internal battery 

When the thermostat is connected to the room heater, it does not use power from the internal battery. 
This  battery  only  serves  to  allow  the  internal  clock  to  run  on  in  case  of  a  power  failure.  The 
programmed  data  always  remains  in  memory.  This  means  that  the  battery,  too,  will  stand  years  of 
use. 
When  the  battery  is  empty,  the  clock  of  the  thermostat  will  be  on  00:00  after  a  power  failure  of  the 
room heater that has number 1. 

Heater 1  33 33 42 80 
CRC:C04D  42 -- -- -- 
Blocking  -- -- -- --  
History:  -- -- -- -- 

Heater 1   1  1 03 09 
CRC:C04D  01 -- -- -- 
Llocking  -- -- -- --  
History:  -- -- -- -- 

Summary of Contents for Multi Therm-C













Reviews: