background image

© 2006 Directed Electronics—all rights reserved

2

H1/12 ORANGE (-) ground-when-armed output

This wire supplies a (-)500 mA ground as long as the system is armed. This output ceases as soon as the 
system is disarmed. The GWA can be hooked up to a window control module, a voice module or any accessory 
that requires a ground when armed.

secondary harness (H2) wire connection guide

H2/1 LIGHT BLUE (-) 200mA 2nd unlock output

This wire provides a second unlock output for progressive locks. Refer to document 1041—

Door Locking 

System Wiring Guide

 for specific applications.

H2/2 WHITE/BLACK 200 mA (-) programmable channel 5 output

This wire provides 200 mA programmable output. (See 

Feature Descriptions

 section of this guide.)

IMPORTANT!

 Never use this wire to drive anything but a relay or a low-current input! This transistorized 

output can only supply 200 mA, and connecting directly to a solenoid, motor, or other high-current device 
will cause the module to fail.

H2/3 VIOLET/BLACK 200 mA (-) programmable channel 4 output

This wire provides 200 mA programmable output. (See 

Feature Descriptions

 section of this guide.)

IMPORTANT!

 Never use this wire to drive anything but a relay or a low-current input! This transistorized 

output can only supply 200 mA, and connecting directly to a solenoid, motor, or other high-current device 
will cause the module to fail.

Summary of Contents for 70.5X







































































Reviews: