manualshive.com logo in svg

CLIFFORD MATRIX 70.5X, Installation Manual

Share
Download
CLIFFORD MATRIX 70.5X Installation Manual Download Page 49

4

3.  

Select  a  Menu.

  Press  and 

HOLD

  the  Valet/Program  switch.  (The 

Valet/Program switch must be plugged into the blue port.) After 
three  seconds  the  siren  will  chirp  once  indicating  entry  to  the 
Basic Features Menu. If this is the menu you wish to access, release 
the button and go on to Step 4. If the button is not released, you 
will jump to the next menu and the siren will chirp twice. There are 
three possible menus. Once you have selected the desired menu, 
release the Valet/Program switch.

4.  

Select a Feature.

 

Press and release the Valet/Program switch the 

number of times corresponding to the feature you wish to change. 
For example, to access the third feature, press and release 3 times. 
Then press the button once more and 

HOLD

 it. The siren will chirp 

the number of times equal to the feature you have accessed.

5.  

Program  the  Feature.

 

While  holding  the  Valet/Program  switch, 

you can toggle the feature on and off using the remote control. 
Pressing the button that arms the system will select the one chirp 
or default setting. Pressing the button that disarms the system will 
select the two chirp setting.

Note:

 Some features have more than two possible settings. Pressing 

�������

 will select the one chirp setting, 

pressing 

�������

 will toggle through the two-chirp and higher settings.)

6.  

Release.

 

Release the Valet/Program switch.

Once a feature is programmed:

■

 

 

Other features can be programmed within the same menu.

■

 

 

Another menu can be selected.

■

 

 

The learn routine can be exited if programming is complete.

Summary of Contents for 70.5X







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands