CLIFFORD MATRIX 70.5X Installation Manual Download | Manualshive

Page: 38 / 70

background image

© 2006 Directed Electronics—all rights reserved

3

programmer interface, 3-pin black plug

The black 3 pin port is provided for programming the unit using the Bitwriter (p/n 998T). When using the
Bitwriter, it is possible to configure any and all of the programmable functions as well as lock the Remote
Control and System Features Learn Routines so that unauthorized users cannot change the configuration or
program remote controls to the unit.

When the learn routines have previously been programmed using the Bitwriter, they may have
been locked. Before proceeding with reprogramming the learn routines, they must be unlocked
with the Bitwriter - this cannot be done manually with the Valet switch.

shock sensor harness, 4-pin connector

GREEN (-) multiplex input, zone 4

Inputs shorter than 0.8 seconds will trigger the Warn Away response, while inputs longer than 0.8 seconds
will trigger full alarm sequence and report Zone Four. If installing an optional Directed Electronics dual stage
sensor, connect to the green wire as shown below. The diagram below eliminates the need for diodes to
isolate the sensors.
Diagram for adding optional Directed Electronics dual stage sensor to green wire (Zone 4):

«
...
36
37
38
39
40
...
»

Summary of Contents for 70.5X







































































Reviews:

No comments

Related manuals for 70.5X

Brand: Ultra Start Pages: 8

Brand: Clifford Pages: 9

Brand: Uniel Pages: 20

Brand: Acumen Pages: 8

Brand: Salusfin Pages: 5

Brand: Autostart Pages: 4

Set & Forget 19956

Brand: ACU-RITE Pages: 12

Brand: Orca Pages: 24

Brand: iHome Pages: 20

EDA-R5000 Zerio plus

Brand: Electro Detectors Pages: 3

Brand: Hama Pages: 6

RadioLINK Ei262

Brand: Ei Electronics Pages: 40

Brand: Quantum Guardian Pages: 20

Brand: PORTMAN Pages: 28

RADIO CONTROLLED ALARM CLOCK WITH SOLAR PANEL

Brand: La Crosse Technology Pages: 8

Brand: Clas Ohlson Pages: 16

Brand: Shenzhen Yongchangda Electronics Pages: 3

Brand: nedis Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands