CLIFFORD MATRIX 70.5X Installation Manual Download | Manualshive

Page: 48 / 70

background image

© 2006 Directed Electronics—all rights reserved

4

3.

Press

to choose the operation menu

4.

Scroll to highlight ZONE and press

to choose the zone menu.

5.

Scroll to highlight the desired zone and press

to choose.

6.

Scroll to highlight the icon to be displayed for that zone and press

to choose.

7.

Press

to save and return to the zone menu or

��

to save the setting and exit.

system features learn routine

The System Features Learn Routine dictates how the unit operates. It is possible to access and change any
of the feature settings using the Valet/program switch. However, this process can be greatly simplified by
using the Bitwriter®. Any of the settings can be changed and then assigned to one of up to four remote
controls. This feature is called Owner Recognition. Each time that particular remote control is used to
disarm the system, the assigned feature settings will be recalled. Owner Recognition is only possible when
programming the unit via the Bitwriter®.

If programming with the Bitwriter®, the learn routine can be locked or unlocked. If the learn
routine has previously been locked, it must be unlocked with Bitwriter® - this cannot be done
manually with the Valet switch.

To enter the System Features Learn Routine™:

1.

Open a door.

(

The GREEN wire, H1/8, or the VIOLET, H1/6 must

be connected.)

2.

Ignition.

Turn the ignition on, then off. (The heavy gauge PINK

wire of the relay satellite must be connected.)

«
...
46
47
48
49
50
...
»

Summary of Contents for 70.5X







































































Reviews:

No comments

Related manuals for 70.5X

Brand: S Fire Pages: 2

Pursuit PRO-9342WOS2

Brand: Audiovox Pages: 6

RADIO CONTROLLED PROJECTION ALARM CLOCK

Brand: La Crosse Technology Pages: 25

Brand: Brigade Pages: 8

Ampac TITANUS PRO-SENS

Brand: Halma Pages: 197

Brand: Geemarc Pages: 2

Brand: Bosch Pages: 2

Brand: Prestige Pages: 8

Brand: Letsfit Pages: 12

NIGHT VISION 30330B

Brand: Equity Pages: 2

Brand: Delton Pages: 31

Brand: iHome Pages: 16

Brand: Satel Pages: 9

Brand: System Sensor Pages: 8

Brand: Greenheck Pages: 8

Brand: HST Pages: 2

Brand: Gasmate Pages: 20

Brand: Bacharach Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands