CLIFFORD MATRIX 70.5X Installation Manual Download | Manualshive

Page: 24 / 70

background image

24

H1/10 WHITE/BLUE remote start (-) activation input

This input comes from the factory set to 2 activation pulses. This means that it is necessary to have 2
consecutive ground pulses on the white/blue wire for the remote start to activate or to deactivate. The
same holds true for the remote control activation when set to a two pulse setting it is necessary to press
the

button twice for the remote start to activate or deactivate.

NOTE:

The number of activation inputs can be programmed to 1 or 2 pulses. This setting affects both the

input wire and the remote control when operating the remote starter.

H1/11 WHITE (+/-) selectable light flash output

As shipped, this wire should be connected to the (+) parking light wire. If the light flash polarity jumper
under the sliding door is moved to the opposite position (see

Internal Programming Jumper

section of this

guide), this wire supplies a (-) 200 mA output. This is suitable for driving (-) light control wires in Toyota,

«
...
22
23
24
25
26
...
»

Summary of Contents for 70.5X







































































Reviews:

No comments

Related manuals for 70.5X

Brand: iDataLink Pages: 12

FREEDOM MICRO II

Brand: MTI Pages: 11

Brand: REIZEN Pages: 7

FireAngel CO-9X

Brand: Sprue Safety Products Pages: 28

Brand: SkyScan Pages: 7

Brand: Kidde Pages: 18

Smart Sound Soother

Brand: Project Nursery Pages: 16

Brand: MeiTrack Pages: 7

Brand: EVERSPRING Pages: 6

VESDA-E VEP-A00

Brand: VESDA Pages: 112

Brand: IKEA Pages: 8

Brand: Certa Pages: 21

Brand: Greenheck Pages: 8

Brand: Silencer Pages: 20

Brand: family first Pages: 2

Brand: Code Alarm Pages: 8

Brand: Universal Pages: 6

Brand: Gembird Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands