49
Figure 4-57
4.6.7
Detect
Go to Detect Menu
In the main menu, from Setting to Detect, you can see motion detect interface. See Figure
4-58.There is three detection types: motion detection, video loss, camera masking.
z
The video loss has no detection region and sensitivity setup and camera masking has no
detection region setup.
z
You can see motion detect icon if current channel has enabled motion detect alarm.
z
You can drag you mouse to set motion detect region without Fn button. Please click OK
button to save current region setup. Right click mouse to exit current interface.
4.6.7.1 Motion Detect
Detection menu is shown as below. See Figure 4-58.
z
Event type: From the dropdown list you can select motion detection type.
z
Channel: Select a channel from the dropdown list to set motion detect function.
z
Enable: Check the box here to enable motion detect function.
z
Region: Click select button, the interface is shown as in Figure 4-59. Here you can set
motion detection zone. There are 396(PAL)/330(NTSC) small zones. The green zone is
current cursor position. Grey zone is the motion detection zone. Black zone is the disarmed
zone. You can click Fn button to switch between the arm mode and disarm mode. In arm
mode, you can click the direction buttons to move the green rectangle to set the motion
detection zone. After you completed the setup, please click ENTER button to exit current
setup. Do remember click save button to save current setup. If you click ESC button to exit
the region setup interface system will not save your zone setup.
z
Sensitivity: System supports 6 levels. The sixth level has the highest sensitivity.
z
Period: Click set button, you can see an interface is shown as in Figure 4-61. Here you can
set for business day and non-business day. In Figure 4-61 click set button, you can see an
interface is shown as in Figure 4-62. Here you can set your own setup for business day and
non-business day.
z
Alarm output: when an alarm occurs, system enables peripheral alarm devices.
z
Latch: when motion detection complete, system auto delays detecting for a specified time.
The value ranges from 1-300(Unit: second)
z
Show message: System can pop up a message to alarm you in the local host screen if you
enabled this function.
z
Alarm upload: System can upload the alarm signal to the network (including alarm centre)
if you enabled current function.
z
Send email: System can send out email to alert you when an alarm occurs.
z
Record channel: Select the channel to activate recording function once an alarm occurred.
Please make sure you have set MD record in encode interface(Main
Summary of Contents for Network Video Recorder
