Clearfield StreetSmart Pre-Assigned FDH Installation Manual Download Page 13

Page: 13 / 17

StreetSmart Pre-Terminated FDH Cabinet

__________________________________________________________

Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected]

Manual 021814 REV A - Jan 2021

Male Connector

• Use of Chemtronics MTP Connector Cleaning Swabs (CC505F) is rec-

ommended. Even after cleaning with a probe cleaner, you should always

clean the pins with this (or an equivalent) type swab. Cleans ALL MTP/

MPO connector end faces. This swab also cleans the “pins” of the male

connector

• Lightly “spot” a QbE-2 wipe on the platen with Electro-Wash PX Fiber

Optic Cleaner, the FiberWash or MX Pen.

• Lightly touch short side of the MTP/MPO Connector Swab to the wetted

area (3-5 secs) to absorb some cleaning solution (DO NOT over saturate

the swab).

• Wipe connector areas to be cleaned, sliding pad from bottom of pad

across and forward to tip of swab, from 1 side to the other, turn over and

use long side to dry in same movement.

Cleaning an MPO/MTP Connector

Summary of Contents for StreetSmart Pre-Assigned FDH


















Search results

Summary of Contents for StreetSmart Pre-Assigned FDH

Reviews:

Related manuals for StreetSmart Pre-Assigned FDH

Brands by name

Popular brands

Clearfield StreetSmart Pre-Assigned FDH, Installation Manual

Search results

Summary of Contents for StreetSmart Pre-Assigned FDH

Reviews:

Related manuals for StreetSmart Pre-Assigned FDH

Brands by name

Popular brands