Clearfield StreetSmart Pre-Assigned FDH Installation Manual Download Page 4 | Manualshive

Page: 4 / 17

background image

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected]

4

StreetSmart Pre-Terminated FDH Cabinet

Installation Manual

_________________________________________________________

Manual 021814 REV A - Jan 2021

Mounting Base to Vault Lid

1.

2.

3.

Remove the access door from the back of the cabi-

net base with a 7/16” socket or can wrench.

Remove the nuts from the threaded studs holding

the cabinet to the base and lift the cabinet from the

base.

Place the cabinet base over the hole in the vault lid.

«
...
2
3
4
5
6
...
»

Summary of Contents for StreetSmart Pre-Assigned FDH


















Reviews:

No comments

Related manuals for StreetSmart Pre-Assigned FDH

Brand: L-Acoustics Pages: 2

Brand: Evolveo Pages: 10

Brand: Panduit Pages: 10

Brand: RocketFish Pages: 12

Brand: RocketFish Pages: 41

Brand: Sven Pages: 6

Brand: InWin Pages: 16

Brand: Vicon Pages: 12

Brand: Diablotek Pages: 1

Brand: Alto Pages: 10

Brand: Alto Pages: 12

Brand: Alto Pages: 16

Brand: Steren Pages: 17

GearRAID GR3630-2S-SB2+

Brand: Raidon Pages: 22

Brand: CRU Pages: 12

Brand: MTX Pages: 16

RDC-400-SATA - RAID Drive Cage 400-SATA...

Brand: 3Ware Pages: 2

Brand: Kitronik Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands