manualshive.com logo in svg

Clearfield StreetSmart Pre-Assigned FDH, Installation Manual, Page: 10 / 17

Share
Download
Clearfield StreetSmart Pre-Assigned FDH Installation Manual Download Page 10

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

10

StreetSmart Pre-Terminated FDH Cabinet

Installation Manual 

 _________________________________________________________

Manual 021814 REV A - Jan 2021

Pre-Loaded Splitters

The StreetSmart Pre-Terminated FDH Cabinet will come with 1x32 WaveSmart 

HD Splitters pre-insttalled. Splitter 1’s feeder leg will be connected to feeder 

port 1, and its distribution legs will be connected to distribution ports 1-32. 

Splitter 2 will connect to feeder port 2, and distribution ports 33-64, and so on, 

for the number of splitters pre-installed in the ordered configuration.

If you wish to pull service from a pre-installed splitter leg, the connector can be 

installed into one of the adapters in the provided staging plates.

Note: 

Splitter legs will be secured in place with a velcro strap around the radius 

fingers.

Staging 

Plates

Splitter 

Cage

Distribution 

Ports

Feeder 

Ports

Summary of Contents for StreetSmart Pre-Assigned FDH


















Reviews:

No comments