Clearfield StreetSmart Pre-Assigned FDH Installation Manual Download | Manualshive

Page: 5 / 17

background image

5

StreetSmart Pre-Terminated FDH Cabinet

__________________________________________________________

Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected]

Manual 021814 REV A - Jan 2021

4.

5.

6.

Place the rectangular washer plates over the

round cutouts in the cabinet base.

Insert the J-bolts through the base of the

rectangular washer plates, ensuring that the

J hook is hooked under a rib of the vault lid

underneath.

Using the washers, lock washers, and nuts

provided, secure the cabinet vase to the

vault lid.

«
...
3
4
5
6
7
...
»

Summary of Contents for StreetSmart Pre-Assigned FDH


















Reviews:

No comments

Related manuals for StreetSmart Pre-Assigned FDH

Brand: Macpower & Tytech Pages: 14

Brand: Transcend Pages: 22

Brand: nvent Pages: 5

Brand: Kraun Pages: 10

Brand: Sonnet Pages: 6

Brand: Sonnet Pages: 14

Brand: Audiodesign Pages: 2

Brand: Vynco Pages: 2

Brand: XCLIO Pages: 4

Brand: easyRAID Pages: 30

Brand: i-tec Pages: 28

MonCaso 301 Series

Brand: Moneual Pages: 12

Brand: Rosewill Pages: 7

Brand: UGREEN Pages: 65

FlashSystem 7200

Brand: IBM Pages: 17

Brand: Panduit Pages: 8

Brand: Icy Box Pages: 16

Brand: L-Acoustics Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands