Clearfield FieldSmart FDP Installation Manual Download Page 10

Page: 10 / 17

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected]

FieldSmart FDP Indoor/Outdoor Wall Boxes

Installation Manual

_________________________________________________________

Manual 022793 REV A - March 2022

Locate the mounting pin typically shipped with the fiber deploy reel.

Use the provided screws from the Deploy Reel pack to install the mounting pin. Tighten the first screw until it is halfway

in. Install the pin, and the second screw. Tighten both screws fully to secure the pin in place.

Mount the Deploy Reel onto the pin. The first position will let the Deploy Reel spin, allowing the fiber to be deployed.

Fully depressing the reel will lock it into place, preventing it from spinning and releasing more fiber.

Installing Deploy Reels

Summary of Contents for FieldSmart FDP


















Search results

Summary of Contents for FieldSmart FDP

Reviews:

Related manuals for FieldSmart FDP

Brands by name

Popular brands

Clearfield FieldSmart FDP, Installation Manual

Search results

Summary of Contents for FieldSmart FDP

Reviews:

Related manuals for FieldSmart FDP

Brands by name

Popular brands