background image

9

FieldSmart FDP Indoor/Outdoor Wall Boxes

__________________________________________________________

Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

Manual 022793 Rev A - March 2022

Locate the U-Mount package typically supplied with the xPAK.

Remove contents from plastic bag and carefully cut the different 

components from the main bracket. There is an instruction card 

included with each U-Mount bracket.

1.

2.

See the Clearview xPAK Installation Manual for splicing instructions, located under the Resources tab of the Clearfield 

website, www.seeclearfield.com.

Viewable here: 

https://www.seeclearfield.com/assets/documents/installation-manuals/clearview-xpak-install-manual.pdf

Once removed, screw the U-Mount bracket and retaining clips into the wall box. The location for this is located on the 

back of the instruction card.

You are now ready to install the xPAK into the wall box. See Clearview xPAK install manual for details. Typical cable/ 

jumper routing is included on the back of the instruction card.

3.

4.

Installing xPAKs

Summary of Contents for FieldSmart FDP


















Reviews: