24
Cleanfix —KS 1100—simply clean
Errors and Solutions
Error
Possible reason
Solution
No function display on the
control instruments:
•
Main Switch/Emergency-
OFF switch is not turn ON /
activated
•
Seat contact—is not acti-
vated
•
Error in electrical contact
•
Battery empty/discharge
•
Press/turn ON red Main
Switc, Turn Key-Switch to
position ON
•
A person must be seated
in the centre of the seat
•
Check electric contacts
•
Fully charge the battery
No function of the drive
motor although displayed /
light on the operator panel
•
Driving direction lever must
be in forwards or back-
wards postion
•
Fuse defect
•
Error in electric contact
•
Control electronic error
•
Seat switch AND accelera-
tor must be activated to
drive
•
Change the fuse
•
Check contacts/terminals
•
Check indication of red
LED
No function of any electric
consumers:
•
Fuse(s) defect
•
Wrong electrical con-
nection constantly dama-
ging the fuses
•
Exchange fuse(s)
•
Check electrical contacts
Check each electrical contact for
errors. Especially check the cy-
lindrical brush if clogged/blocked
by ropes, bands, strings, wastes
The sweeping result is not
satisfactory:
•
The side brushes and cy-
lindrical brush were not
lowered yet
•
Side brushes or Cylindrical
brush are damaged
•
The overthrow area is clog-
ged by wastes
•
Cylindrical brush does not
work
•
Too much dust formation
•
Saugpumpe ohneFunktion
•
Filter is very dirty
•
Filter not correctly posi-
tioned
•
Sealing leakeages and
hence the suction of false
air from outside in the area
of the filter chamber
•
Let down all three levers to
lower the brushes. 2 levers
on steering / one near seat
•
Replace, readjust the
damaged brushes
•
Check if the cylindrical
brush cover has catched
wastes inside
•
Is it correctly mounted.
Does the drive motor turn?
•
Switch off side brushes
•
Check for electric damage
•
Clean the filter properly
•
Check if filter is properly
fitted and fastened
•
Check where the sealing is
damaged and false air is
sucked.
9
Cleanfix —KS 1100—simply clean
Operation
Adjustment of the driver seat
Undo the seat fixation and move the driver
seat on the it‘s seat console until you have
found the suitable sitting position.
Drive operation/Starting the Sweeper
Safety instructions
The Ride-on-Sweeper can only be used by
reliable persons. Only trained and well
instructed persons shall be used. The
responsibilities must be clearly fixed.
Always check the Ride-On-Sweeper before
any drive and test the functionability.and
technical safety.
Do not use the machine if it should have a
defect. Only drive on the tracks and areas
which are strictly assigned for the Ride-on-
Sweeper. The Ride-On-Sweeper is strictly
designed for only one person to use. The
transportation of more than one person is
strictly forbidden.
•
Seat yourself on the drivers seat.
The Ride-on-Sweeper cannot be put
into operation, if the drivers seat is
not exposed to weight pressure to
switch the contact.
•
Check the position of the switch of
the lever on the operator panel.
•
The
F
ilter cleaning switch must be
in OFF (AUS) position.
•
The red
M
ain Switch must be in ON
(EIN) position.
•
The
K
ey switch must be ON
•
Check the battery charge status- -
indication on the operator panel.
The luminious LED‘s shine in
sequence and then show the
effective charging status of the
batteries.
•
Press the brake
•
Release the emergency-brake
fixation (next to the brake)
-
Driving forwards:
•
Move the lever switch to the front
for actuation „drive forwards“. Only
when the accelerator has been
pressed down, then the Ride-on-
Sweeper will start driving.
- Driving backwards:
•
Move the lever switch to the back
for actuation „drive backwards“.
Only when the accelerator has
been pressed down, then the Ride-
on-Sweeper will go backwards.
•
An acoustic signal is optional
•
The speed of the Ride-on-Sweeper
can be chosen variably when
pressing down the accelerator.
Accelerator
Brake pedal Brake fixation
Light switch
Lever
switch:
forward/backwards
Horn
