Claydon HYBRID M3F Operator'S Manual Download Page 21 | Manualshive

Page: 21 / 60

background image

21

F

DIRECTIVE PROVISIONS

OPERATORS MANUAL - HYBRID - M3F & M4RF

Directive Provisions

This Claydon Hybrid Seed Drill conforms to Machinery Directive 2006/42/EC (see Declaration of Conformity
at the front of the manual).

AIRBORNE NOISE EMISSIONS

The A-weighted emission sound pressure level of measurements taken directly at the fan is 94dBA.

WARNING AND CAUTION

These warnings and cautions must be observed when operating the Hybrid Seed Drill.

• Ensure total weight of tractor/drill combination does not exceed permitted limits and weight of tractor is

sufficient for safe field and road use.

• Do not allow anyone to stand between tractor and machine during coupling/uncoupling procedures.

• For maintenance/adjustment of the machine ensure that it is lowered to the ground.

• Seed dressing may be highly poisonous so protective measures-gloves, goggles, face-mask must be used while
loading the hopper and cleaning the machine after use with compressed air.

• The hydraulic system on the machine operates under high pressure. Pressurised hydraulic oil is dangerous
so connecting/disconnecting the drill must only be undertaken with the tractor engine turned off and the

pressure in the hoses released.

• Before operating the machine ensure no-one is standing within range of its turning circle-including the

marker arms.

• The Tungsten points on the leading tines should be protected when lowering onto concrete or paved
surfaces by placing wooden boards under the tines.

Directive Provisions

!

WARNING SYMBOLS

Warning

- Always pay extra attention to any text next to this symbol. This symbol could

relate to something which can cause damage to the machine, serious injury or death. Please

take the relevant precautions to avoid dangerous situations.

Eye Protection is required

- In the interest of safety, eye protection must be worn.

Gloves are required

- In the interest of safety, gloves must be worn.

!

Please Note

- Information relating to this symbol may be worth noting as a useful tip to

help use the machine more effectively.

«
...
19
20
21
22
23
...
»

Summary of Contents for HYBRID M3F





























































Reviews:

No comments

Related manuals for HYBRID M3F

Brand: OfiTE Pages: 21

Brand: Earthlite Pages: 4

Brand: YATEK Pages: 78

Brand: vanEE Pages: 52

Brand: Caddon Hives Pages: 3

PowerXL DX-NET-ETHERNET2-2

Brand: Eaton Pages: 48

Power Xpert C445

Brand: Eaton Pages: 2

Brand: Gaspardo Pages: 44

Brand: Abus Pages: 12

FUSION APOLLO MS-WB675

Brand: Garmin Pages: 18

Brand: Rapid Shape Pages: 12

MultiFill 003-561-005

Brand: Hanskamp Pages: 20

REBOUND DUAL ST

Brand: Össur Pages: 104

Brand: Össur Pages: 130

Brand: Woodward Pages: 62

Brand: Crosley Pages: 6

Brand: Gambro Pages: 273

Brand: SAC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands