Clavister NetWall W20A Getting Started Manual Download Page 76 | Manualshive

Page: 76 / 89

background image

Chapter 7: Safety Precautions

Safety Precautions

Clavister W20B devices are

Safety Class I

products and have protective ground terminals. There

must be an uninterrupted safety earth ground from the main power source to the product’s
input wiring terminals, power cord, or supplied power cord set. Whenever it is likely that the
protection has been impaired, disconnect the power cord until the ground has been restored.

For LAN cable grounding:

•

If your LAN covers an area served by more than one power distribution system, be sure their
safety grounds are securely interconnected.

•

LAN cables may occasionally be subject to hazardous transient voltage (such as lightning or
disturbances in the electrical utilities power grid). Handle exposed metal components of the
network with caution.

There are no user-serviceable parts inside these products. Only service-trained personnel can
perform any adjustment, maintenance or repair.

Säkerhetsföreskrifter

Dessa produkter är säkerhetsklassade enligt klass I och har anslutningar för skyddsjord. En
obruten skyddsjord måste finnas från strömkällan till produktens nätkabelsanslutning eller
nätkabel. Om det finns skäl att tro att skyddsjorden har blivit skadad, måste produkten stängas
av och nätkabeln avlägnas till dess att skyddsjorden har återställts.

För LAN-kablage gäller dessutom att:

•

om LAN:et täcker ett område som betjänas av mer än ett strömförsörjningssystem måste
deras respektive skyddsjord vara ihopkopplade.

•

LAN kablage kan vara föremål för farliga spänningstransienter (såsom blixtnedslag eller
störningar i elnätet). Hantera metallkomponenter i förbindelse med nätverket med
försiktighet.

Det finns inga delar i produkten som kan lagas av användaren. All service samt alla justeringar,
underhåll eller reparationer får endast utföras av behörig personal.

76

«
...
74
75
76
77
78
...
»

Summary of Contents for NetWall W20A


























































































Reviews:

No comments

Related manuals for NetWall W20A

LS42 - BladeCenter - 7902

Brand: IBM Pages: 56

Brand: IBM Pages: 2

BladeCenter Management Module

Brand: IBM Pages: 78

Brand: IBM Pages: 110

Remote Supervisor Adapter II

Brand: IBM Pages: 132

Brand: Ubiquiti Pages: 50

Compact Emulator M30620T-CPE

Brand: Renesas Pages: 52

Brand: I-O Wireless Pages: 55

Brand: u-blox Pages: 29

RP614 - Web Safe Router

Brand: NETGEAR Pages: 16

Brand: LevelOne Pages: 26

Brand: Xyclop Pages: 144

Brand: Silvertel Pages: 9

Brand: Comway Pages: 20

Brand: S&T Pages: 28

Brand: Omron Pages: 29

airMAX NanoBridge M NBM3

Brand: Ubiquiti Pages: 24

SmartRack SR25UBEXP

Brand: Tripp Lite Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands