Clarke X-Pro CAT202 Operating & Maintenance Instructions Download

Page: 29 / 32

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

PARTS LIST-DIE GRINDER

ACCESSORIES

A wide range of accessories is available including filter/regulators, lubricators,
high-pressure hoses (5 to 50 metres) etc.

Contact your CLARKE dealer or the CLARKE International Service Department
for further information.

A wide range of 1/2” square drive socket sets is available in the CLARKE
catalogue.

CLARKE Air Line Oil (part no. 3050825) is available from your CLARKE dealer.

Description

Main Housing

O-ring

Housing liner

Screw

Bushing

Bearing

O-ring

Rear plate

Trigger

Set pin

Lever

Rotor

Spring

Rotor blade

Roll pin

Cylinder

Trigger pin

Bushing

Air inlet

Front plate

Spring

Steel ball

Bearing

O-ring

Collet seat

Air regulator

Lock ring

O-ring

Decoration ring

Exhaust deflector

Front protective cover

O-ring

Collet

O-ring

Collet jacket

Valve stem

Small wrench

Spring

Large wrench

Summary of Contents for X-Pro CAT202

































Search results

Summary of Contents for X-Pro CAT202

Reviews:

Related manuals for X-Pro CAT202

Brands by name

Popular brands

Clarke X-Pro CAT202, Operating & Maintenance Instructions

Search results

Summary of Contents for X-Pro CAT202

Reviews:

Related manuals for X-Pro CAT202

Brands by name

Popular brands